42-1008 power transformer

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

42-1008 power transformer

Eric T
Senior Member

Posts: 298
Threads: 22
Joined: May 2012
City: Chattanooga State, Province, Country: TN

#11

09-04-2013, 10:34 PM

Marty has a good point. I pulled off my transformer and replaced the wires coming out of it because the insulation was worn through where it came out of the clamshell. Just take tons of pictures and make notes of exactly where everything connected.

By the way, I'm guessing the wire going to the 41 is either B or ground for the filament circuit. Mine goes to one of the pins of the socket on the rear of the chassis, then over to of the filament pins (the two fat pins) of a 41.

It's not how bad you mess up, it's how well you can recover.

(This post was last modified: 09-04-2013, 10:53 PM by Eric T.)

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

42-1008 power transformer - by davidff - 08-21-2013, 10:22 AM

RE: 42-1008 power transformer - by Jim Dutridge - 08-21-2013, 11:37 AM

RE: 42-1008 power transformer - by davidff - 08-26-2013, 10:08 AM

RE: 42-1008 power transformer - by BrendaAnnD - 08-26-2013, 02:57 PM

RE: 42-1008 power transformer - by codefox1 - 08-26-2013, 03:20 PM

RE: 42-1008 power transformer - by davidff - 09-03-2013, 07:43 AM

RE: 42-1008 power transformer - by Eric T - 09-03-2013, 07:39 PM

RE: 42-1008 power transformer - by Eric T - 09-03-2013, 11:08 PM

RE: 42-1008 power transformer - by marty - 09-04-2013, 12:05 AM

RE: 42-1008 power transformer - by davidff - 09-04-2013, 05:41 PM

RE: 42-1008 power transformer - by Eric T - 09-04-2013, 10:34 PM

RE: 42-1008 power transformer - by davidff - 09-19-2013, 11:31 AM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

Who's Online

There are currently 766 online users. [Complete List]
» 1 Member(s) | 765 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me