1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Speaking of Vibrators
TA Forbes
Deviate Emeritus
*****
Posts: 2,353
Threads: 92
Joined: May 2010
City: Clayton, NC
#1

09-24-2013, 06:47 PM
http://www.ebay.com/itm/221276221546?ssP...1423.l2649

This is a 32V vibrator Brenda found for me in eBay. I have been looking for one to replace the smoked one in my Philco 32 Tombstone.

Although it (above) is a "plug in" type and is quite a bit different than that found in the 32, I believe that I could make it work.

BUT..... Note that vibrator is a 100 CPS model. I have no idea what the HZ output of the original is, and guess I assumed it to be 60 Hz.

Question to all of you: Will this 100 Hz vibrator work (assuming it can be "plumbed" to do so) in my Philco 32

PS- Mike.... I KNOW you were hoping, after seeing the title of this thread, for something naughty. Sorry. I'll try harder next time.
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Speaking of Vibrators - by TA Forbes - 09-24-2013, 06:47 PM
RE: Speaking of Vibrators - by BrendaAnnD - 09-24-2013, 08:15 PM
RE: Speaking of Vibrators - by Arran - 09-24-2013, 09:37 PM
RE: Speaking of Vibrators - by TA Forbes - 09-26-2013, 01:29 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration