1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Pilot lamp blows out
BrendaAnnD
Phorum Expert
*****
Posts: 1,106
Threads: 88
Joined: Jun 2011
City: Tacoma State, Province, Country: Washington
#3

10-16-2013, 08:25 PM
Clean the socket for the 35Y4 thoroughly. If there's a tiny bit of oxidization on the tube pins or the socket, the pins are loose, it can cause this.
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Pilot lamp blows out - by Buzz - 10-16-2013, 07:27 PM
RE: Pilot lamp blows out - by Radioroslyn - 10-16-2013, 08:06 PM
RE: Pilot lamp blows out - by BrendaAnnD - 10-16-2013, 08:25 PM
RE: Pilot lamp blows out - by Buzz - 10-16-2013, 09:04 PM
RE: Pilot lamp blows out - by LASJayhawk - 10-16-2013, 10:47 PM
RE: Pilot lamp blows out - by Buzz - 10-17-2013, 10:37 AM
RE: Pilot lamp blows out - by LASJayhawk - 10-17-2013, 01:14 PM
RE: Pilot lamp blows out - by Buzz - 10-21-2013, 07:28 PM
RE: Pilot lamp blows out - by Randy H. - 11-12-2013, 07:36 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT-6 finished!!
Well the 35Z3 doesn't have a tap on the tube heater for a pilot light, so in this set they have the dial lamp paralleled...Arran — 06:21 PM
Electrolytic restuffing/internals
Thanks. I think I try to cut this as suggested. I don’t have a lathe, but I do have a tap and die set. I am going to see...bridkarl — 04:46 PM
Another amp build - here I go again!
Hey all! Well, I guess that with what I learned from my last build, it's time to move up the ladder another rung and tak...TV MAN — 04:38 PM
Electrolytic restuffing/internals
There are various ways to handle this, one is to cut near just above that rolled in area is near the bottom, using the r...Arran — 04:36 PM
philco predicta
If you have a television signal generator (a must-have for TV repair) and an oscilloscope (the same), then this problem ...RadioSvit — 04:23 PM
HiFi (Chifi) tube amp build - but my own design.
Thanks Rod for the offer but I don't think those would work. There's some differences in the sizing and mounting holes b...TV MAN — 03:13 PM
philco predicta
Bob Anderson (Bandersontv) on Youtube would be the go-to guy on these. Lots of good videos. I don't know what model you ...TV MAN — 03:02 PM
Electrolytic restuffing/internals
I have an issue on a non-Philco radio which I expect to run into on a whole set of Philcos and others. I have an 8mf ...bridkarl — 01:17 PM
Philco model 38 code 121 not receiving signal.
Thank you sir. I thought about it and decided to put it up in the arch support. I was looking at the chassis and didn't ...Stormlord5500 — 06:24 AM
Philco model 38 code 121 not receiving signal.
Congrats on your success Stormlord. My rough guess is that since both the 15 and the 1A6 are supposed to be shielded, I...MrFixr55 — 10:04 PM

[-]
Who's Online
There are currently 725 online users. [Complete List]
» 1 Member(s) | 724 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration