How best to restick veneer

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

How best to restick veneer

phly guy
Member

Posts: 61
Threads: 14
Joined: May 2008

06-08-2008, 04:24 PM

Well, there's the rub. some of it is on flat surfaces but most of it is on curved surfaces. CyA glue would work well from the standpoint of quick cure so I could hold the pieces in place. But seems that sounds like a bad idea to you. I can understand that.

I'm pretty sure that the areas that need re-attached can be pressed and/or weighted to hold them down while they dry. Most of them are on the sides rather than the front so not extremely noticeable.

John.

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

How best to restick veneer - by phly guy - 06-08-2008, 01:18 AM

[No subject] - by exray - 06-08-2008, 07:29 AM

[No subject] - by phly guy - 06-08-2008, 04:24 PM

[No subject] - by exray - 06-08-2008, 06:23 PM

[No subject] - by phly guy - 06-09-2008, 05:45 PM

[No subject] - by phly guy - 06-09-2008, 05:52 PM

[No subject] - by exray - 06-09-2008, 08:07 PM

[No subject] - by phly guy - 06-10-2008, 08:48 AM

Re: How best to restick veneer - by Robert - 12-28-2008, 05:15 PM

Re: How best to restick veneer - by exray - 12-29-2008, 08:19 AM

Re: How best to restick veneer - by radiomikee - 01-01-2009, 11:45 AM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM
Testing a speaker and output transformer Trutone A2-G
morzh Short-circuited turns can be considered as a half-dead transformer. But on this case transformer will hot and s...Vlad95 — 11:01 AM
Testing a speaker and output transformer Trutone A2-G
I am not sure how a transformer could be weak. It could be inadequate, but only when you replace the original with somet...morzh — 09:56 AM

Who's Online

There are currently 2305 online users. [Complete List]
» 3 Member(s) | 2302 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me