1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 46-1203, radio doesn't work.
Guest
Unregistered
 
#9

06-19-2008, 11:59 AM
The 46-1203 that I'm working on has an intermittent filament circuit problem. The tubes and filament connections on the tube sockets seem ok, so I suspect a poor connection in the filament resistor that is mounted outboard of the chassis. The circuit seems to open up after the set has been running for a while.
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Philco 46-1203, radio doesn't work. - by Guest - 02-04-2008, 09:47 PM
[No subject] - by TonyJSenior - 02-05-2008, 06:07 PM
[No subject] - by TonyJSenior - 02-05-2008, 07:48 PM
[No subject] - by Guest - 02-06-2008, 04:28 AM
[No subject] - by TonyJSenior - 02-06-2008, 08:26 AM
[No subject] - by Guest - 02-06-2008, 01:14 PM
[No subject] - by TonyJSenior - 02-06-2008, 01:23 PM
46-1203 volume control - by Guest - 06-19-2008, 11:44 AM
46-1203 volume control - by Guest - 06-19-2008, 11:59 AM
[No subject] - by gary rabbitt - 06-20-2008, 02:06 PM
Re: Philco 46-1203, radio doesn't work. - by Guest - 07-19-2008, 03:38 AM
Re: 46-1203 volume control - by Guest - 07-19-2008, 03:43 AM
philco 46-1203 - by Guest - 08-30-2008, 12:03 AM
[No subject] - by BDM - 08-30-2008, 01:13 AM
Re: Philco 46-1203, radio doesn't work. - by Guest - 09-04-2008, 12:14 AM
Re: Philco 46-1203, radio doesn't work. - by Guest - 09-04-2008, 02:09 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco model 38 code 121 not receiving signal.
I think this thing is way more accurate than my Walmart DMM. :DStormlord5500 — 08:19 AM
Philco model 38 code 121 not receiving signal.
Thankyou for the kind words sir. I double checked it with my component tester and it read 2.7 ohms at .02mH.Stormlord5500 — 08:14 AM
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM

[-]
Who's Online
There are currently 760 online users. [Complete List]
» 1 Member(s) | 759 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration