1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Model 610 electrolytic condensers
Kestas
Member
***
Posts: 178
Threads: 19
Joined: Feb 2014
City: The Motor City,Detroit MI
#4

03-05-2014, 01:56 PM
If you perhaps take pictures before starting, could you take a closeup of the area that has the resistors R39, R40, and R42? That area in my unit was repaired at one point, and I'd like to verify the connections and appearance of the resistors. R39 looks charred on mine, even though it ohms out okay.
(This post was last modified: 03-05-2014, 01:58 PM by Kestas.)
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Model 610 electrolytic condensers - by Kestas - 03-02-2014, 06:54 PM
RE: Model 610 electrolytic condensers - by morzh - 03-02-2014, 08:16 PM
RE: Model 610 electrolytic condensers - by TV MAN - 03-05-2014, 10:47 AM
RE: Model 610 electrolytic condensers - by Kestas - 03-05-2014, 01:56 PM
RE: Model 610 electrolytic condensers - by TV MAN - 03-05-2014, 03:17 PM
RE: Model 610 electrolytic condensers - by Kestas - 03-05-2014, 06:32 PM
RE: Model 610 electrolytic condensers - by TV MAN - 03-16-2014, 03:52 PM
RE: Model 610 electrolytic condensers - by Kestas - 03-17-2014, 09:40 PM
RE: Model 610 electrolytic condensers - by TV MAN - 03-18-2014, 10:51 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration