Polishing Plastic Knobs

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Polishing Plastic Knobs

Texasrocker
Phorum Expert

Posts: 909
Threads: 117
Joined: Jun 2007

07-23-2008, 10:54 PM

I have had good results using .0000 steel wool saturated with "Glazit" bakelight telephone refinisher in some cases. Icon_wink

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

Polishing Plastic Knobs - by Owells - 07-08-2008, 07:04 PM

[No subject] - by Steve Davis - 07-08-2008, 08:45 PM

Re: Polishing Plastic Knobs - by Syl - 07-08-2008, 09:01 PM

Brasso - by BILL - 07-12-2008, 12:03 PM

[No subject] - by englishradioman - 07-12-2008, 07:56 PM

[No subject] - by Texasrocker - 07-23-2008, 10:54 PM

[No subject] - by Chuck Schwark - 07-23-2008, 11:01 PM

[No subject] - by exray - 07-24-2008, 07:52 AM

[No subject] - by Terry Judkins - 07-24-2008, 09:39 AM

[No subject] - by Syl - 07-25-2008, 11:15 AM

[No subject] - by englishradioman - 07-25-2008, 05:25 PM

[No subject] - by etech - 08-01-2008, 01:58 PM

[No subject] - by englishradioman - 08-01-2008, 04:20 PM

Re: Polishing Plastic Knobs - by Guest - 02-07-2009, 02:31 PM

Re: Polishing Plastic Knobs - by jayoungs - 02-09-2009, 10:53 AM

Re: Polishing Plastic Knobs - by radiorich - 02-15-2009, 05:07 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM
Testing a speaker and output transformer Trutone A2-G
morzh Short-circuited turns can be considered as a half-dead transformer. But on this case transformer will hot and s...Vlad95 — 11:01 AM
Testing a speaker and output transformer Trutone A2-G
I am not sure how a transformer could be weak. It could be inadequate, but only when you replace the original with somet...morzh — 09:56 AM

Who's Online

There are currently 2205 online users. [Complete List]
» 1 Member(s) | 2204 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me