Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

any tube hifi audiophools here?
#11

Aye. Williamsons are very good if you can get the iron. Too bad you need a kid to tell the difference if you are most of us.

(edit) There still needs to be some consideration to harmonics as in all amps, and usually a small high voltage capacitor across the primary will take care of it (if it opens up, yup, tweeter toast!), along with the other common precautions such as resistors in series with, and after coupling capacitor, and resistors between screen grid and it's winding. I've seen 1K 2 watts used for this purpose a few times.


Messages In This Thread
any tube hifi audiophools here? - by Texasrocker - 07-20-2009, 02:01 AM
RE: any tube hifi audiophools here? - by codefox1 - 04-02-2014, 02:48 PM
RE: any tube hifi audiophools here? - by wa2ise - 04-24-2014, 09:53 AM
Re: any tube hifi audiophools here? - by kruc - 07-20-2009, 04:08 AM
Re: any tube hifi audiophools here? - by Arran - 07-20-2009, 06:38 AM
Re: any tube hifi audiophools here? - by Arran - 07-20-2009, 06:48 AM
Re: any tube hifi audiophools here? - by codefox1 - 07-20-2009, 02:54 PM
Re: any tube hifi audiophools here? - by kruc - 07-21-2009, 10:32 PM
Re: any tube hifi audiophools here? - by Arran - 08-03-2009, 12:19 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently no members online.

>