Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 38-690 tweeter improvement
#14

Dave Slusarczyk Wrote:
Ron Ramirez Wrote:Hi Dave

A properly restored 38-690 should deliver deep bass and noticeable treble - with the bass control set to max, and the Fidelity-Selectivity control set to maximum fidelity.

And, yes, a properly restored 38-690 will, most definitely, put any lower tube count set to shame, without a doubt.

I've owned one in the past...and had a few pass through here as repair jobs...so I know how they should sound; quite simply, SUPERB.

Thanks Ron,

I wish I had one to compare it to. If I turn the bass up all the way up and the treble all the way it does sound good. I just never thought one would typically play set with both adj to max.


Thanks Ron,
Dave

Correct me if I'm wrong. Most bass and treble controls on old radios only cut bass and treble they can't add any like newer equipment does. So having both wide open should give flat response. Keep in mind a good set does boost the bass at low listening levels. Also do to the 690's design aka bass amp bass would be greatly exaggerate at low listening levels with the control cranked.

Bill

It's not what you don't know that hurts you it's what you know that's not so.


Messages In This Thread
Re: Philco 38-690 tweeter improvement - by Syl - 07-25-2008, 11:16 AM
Re: Philco 38-690 tweeter improvement - by Syl - 07-25-2008, 09:19 PM
[No subject] - by Ron Ramirez - 07-25-2008, 10:39 PM
[No subject] - by wonderwrench - 07-25-2008, 10:52 PM
[No subject] - by Ron Ramirez - 07-25-2008, 11:49 PM
[No subject] - by Dave Slusarczyk - 07-25-2008, 11:53 PM
[No subject] - by wonderwrench - 07-26-2008, 12:06 AM
[No subject] - by Ron Ramirez - 07-26-2008, 12:06 AM
[No subject] - by Ron Ramirez - 07-26-2008, 12:13 AM
[No subject] - by Dave Slusarczyk - 07-26-2008, 12:59 AM
[No subject] - by BDM - 07-26-2008, 01:40 AM
[No subject] - by wonderwrench - 07-26-2008, 01:48 AM
[No subject] - by wonderwrench - 07-26-2008, 02:30 AM
[No subject] - by Syl - 07-26-2008, 09:33 AM
[No subject] - by Ron Ramirez - 07-26-2008, 10:20 AM
[No subject] - by Syl - 07-26-2008, 12:52 PM
[No subject] - by Dave Slusarczyk - 07-26-2008, 04:33 PM
[No subject] - by wonderwrench - 07-26-2008, 04:47 PM
[No subject] - by wonderwrench - 07-26-2008, 04:53 PM
[No subject] - by Ron Ramirez - 07-26-2008, 05:40 PM
[No subject] - by Syl - 07-26-2008, 05:51 PM
[No subject] - by Syl - 07-26-2008, 05:55 PM
[No subject] - by Dave Slusarczyk - 07-26-2008, 06:50 PM
[No subject] - by Syl - 07-26-2008, 08:17 PM
[No subject] - by Dave Slusarczyk - 07-26-2008, 10:26 PM
[No subject] - by Syl - 07-27-2008, 12:11 AM
[No subject] - by Dave Slusarczyk - 07-27-2008, 02:02 PM
[No subject] - by Terry Judkins - 07-27-2008, 06:59 PM
[No subject] - by wonderwrench - 07-27-2008, 07:11 PM
[No subject] - by Dave Slusarczyk - 07-27-2008, 07:53 PM
[No subject] - by wonderwrench - 07-27-2008, 10:00 PM
[No subject] - by Syl - 07-28-2008, 11:21 AM
[No subject] - by Dave Slusarczyk - 07-28-2008, 06:10 PM
[No subject] - by BDM - 07-28-2008, 06:17 PM
[No subject] - by Ron Ramirez - 07-28-2008, 06:59 PM
[No subject] - by Dave Slusarczyk - 07-28-2008, 07:12 PM
[No subject] - by Syl - 07-28-2008, 09:33 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco Model 38-7: what caps & resistors do fail typically?
Since you stated earlier, you have a console 38-7XX.  They also had a 38-7T (table), and 38-7CS (chairside).  A very nic...GarySP — 01:18 PM
Part numbers to model cross
That I wouldn't know, but sometimes the radio document itself shows one, same as the capacitor cans' etc pinouts.morzh — 12:46 PM
Part numbers to model cross
Thank you morzh, that is exactly what I was looking for. Now , is there some where that shows pinouts for Philco power ...Jim Dutridge — 11:37 AM
Restoration of the Canadian General Electric A-87
Thanks for your help Michael. In fact, this video is only an intermediate result. Later I had to apply another tinting l...RadioSvit — 09:01 AM
Restoration of the Canadian General Electric A-87
Great job on the cabinet. PS. In the US notation, "kenotron" refers to specific type of tubes; we call re...morzh — 08:24 AM
Part numbers to model cross
This document has at least some tables of models and parts used. Example: Choke 32-7572, used in 604 radio. Search f...morzh — 08:19 AM
Restoration of the Canadian General Electric A-87
I also checked all the radio tubes on my Hickok 530 tube tester. The 5Z3 kenotron turned out to be faulty, all the other...RadioSvit — 08:02 AM
Restoration of the Canadian General Electric A-87
Well... While the varnish is drying up, I started repairing the chassis... Of course I started by replacing the pa...RadioSvit — 07:12 AM
Philco Model 38-7: what caps & resistors do fail typically?
Hello Martin, Welcome aboard our little community what great Model 38-7 Sincerely Richardradiorich — 12:30 AM
Philco Model 38-7: what caps & resistors do fail typically?
Welcome to the Phorum Martin. I count about 9 paper caps, the 3 electrolytic caps and 2-Y2 safety caps to replace th...RodB — 09:44 PM

[-]
Who's Online
There are currently no members online.

>