1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 46-1203, radio doesn't work.
Guest
Unregistered
 
#13

08-30-2008, 12:03 AM
It turned out that the audio output tube had an intermittent heater filament. Once that tube was replaced, the radio stopped cutting out. I've read that audio output tubes can develop intermittent filaments because their power load. The filament didn't cut out when the tube was tested in my tube checker.
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Philco 46-1203, radio doesn't work. - by Guest - 02-04-2008, 09:47 PM
[No subject] - by TonyJSenior - 02-05-2008, 06:07 PM
[No subject] - by TonyJSenior - 02-05-2008, 07:48 PM
[No subject] - by Guest - 02-06-2008, 04:28 AM
[No subject] - by TonyJSenior - 02-06-2008, 08:26 AM
[No subject] - by Guest - 02-06-2008, 01:14 PM
[No subject] - by TonyJSenior - 02-06-2008, 01:23 PM
46-1203 volume control - by Guest - 06-19-2008, 11:44 AM
46-1203 volume control - by Guest - 06-19-2008, 11:59 AM
[No subject] - by gary rabbitt - 06-20-2008, 02:06 PM
Re: Philco 46-1203, radio doesn't work. - by Guest - 07-19-2008, 03:38 AM
Re: 46-1203 volume control - by Guest - 07-19-2008, 03:43 AM
philco 46-1203 - by Guest - 08-30-2008, 12:03 AM
[No subject] - by BDM - 08-30-2008, 01:13 AM
Re: Philco 46-1203, radio doesn't work. - by Guest - 09-04-2008, 12:14 AM
Re: Philco 46-1203, radio doesn't work. - by Guest - 09-04-2008, 02:09 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco model 38 code 121 not receiving signal.
I think this thing is way more accurate than my Walmart DMM. :DStormlord5500 — 08:19 AM
Philco model 38 code 121 not receiving signal.
Thankyou for the kind words sir. I double checked it with my component tester and it read 2.7 ohms at .02mH.Stormlord5500 — 08:14 AM
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM

[-]
Who's Online
There are currently 762 online users. [Complete List]
» 1 Member(s) | 761 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration