1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 42-1015P
davidff
Member
***
Posts: 83
Threads: 30
Joined: Aug 2011
City: SOUTHINGTON, CT
#5

07-21-2014, 10:45 AM
I ended up paying $150 for the console. The chassis is very clean, the cabinet is a 9 out of 10, and, of course the phono has the rubber drive wheel with cracked rubber, but the BOL changer looks pretty clean, and is complete. The mohogany cabinets are not bad looking also. Hopefully I can get it going, after I figure out how to get home in my van. It weighs a ton. I will send up some pics once I get it home. Its like Christmas in July.
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Philco 42-1015P - by davidff - 07-16-2014, 01:05 PM
RE: Philco 42-1015P - by codefox1 - 07-16-2014, 03:47 PM
RE: Philco 42-1015P - by Ron Ramirez - 07-16-2014, 05:03 PM
RE: Philco 42-1015P - by davidff - 07-17-2014, 08:24 AM
RE: Philco 42-1015P - by davidff - 07-21-2014, 10:45 AM
RE: Philco 42-1015P - by Radioroslyn - 07-21-2014, 01:21 PM
RE: Philco 42-1015P - by 78zenithtv - 07-11-2017, 12:16 PM
RE: Philco 42-1015P - by morzh - 07-11-2017, 12:29 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Another amp build - here I go again!
Sweet! I actually have a Dynaco Mark 4 that I had been running with 6L6s with no mods. Seemed to my 14-year-old head a...MrFixr55 — 12:57 AM
PT-6 finished!!
Hi Gang, Tube heaters are not "Ohmic" devices (that maintain specified resistance over wide temperature, c...MrFixr55 — 12:03 AM
Electrolytic restuffing/internals
Look here: Philco-F676-124 Vlad95 — 08:02 PM
PT-6 finished!!
Well the 35Z3 doesn't have a tap on the tube heater for a pilot light, so in this set they have the dial lamp paralleled...Arran — 06:21 PM
Electrolytic restuffing/internals
Thanks. I think I try to cut this as suggested. I don’t have a lathe, but I do have a tap and die set. I am going to see...bridkarl — 04:46 PM
Another amp build - here I go again!
Hey all! Well, I guess that with what I learned from my last build, it's time to move up the ladder another rung and tak...TV MAN — 04:38 PM
Electrolytic restuffing/internals
There are various ways to handle this, one is to cut near just above that rolled in area is near the bottom, using the r...Arran — 04:36 PM
philco predicta
If you have a television signal generator (a must-have for TV repair) and an oscilloscope (the same), then this problem ...RadioSvit — 04:23 PM
HiFi (Chifi) tube amp build - but my own design.
Thanks Rod for the offer but I don't think those would work. There's some differences in the sizing and mounting holes b...TV MAN — 03:13 PM
philco predicta
Bob Anderson (Bandersontv) on Youtube would be the go-to guy on these. Lots of good videos. I don't know what model you ...TV MAN — 03:02 PM

[-]
Who's Online
There are currently 252 online users. [Complete List]
» 4 Member(s) | 248 Guest(s)
AvatarAvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration