Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 1 Vote(s) - 5 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 70 Reproduction Cabinet
#32

...and it is a challenge, cosnidering the delicate latticework of 20's grill. And the Deluxe's shadowing front panel pattern.


Messages In This Thread
Philco 70 Reproduction Cabinet - by Steve Davis - 08-02-2014, 08:36 PM
RE: Philco 70 Reproduction Cabinet - by morzh - 08-02-2014, 09:31 PM
RE: Philco 70 Reproduction Cabinet - by gregb - 08-02-2014, 10:18 PM
RE: Philco 70 Reproduction Cabinet - by Arran - 08-02-2014, 10:23 PM
RE: Philco 70 Reproduction Cabinet - by Arran - 08-02-2014, 11:40 PM
RE: Philco 70 Reproduction Cabinet - by tab10672 - 08-03-2014, 12:31 AM
RE: Philco 70 Reproduction Cabinet - by Arran - 08-03-2014, 12:45 AM
RE: Philco 70 Reproduction Cabinet - by codefox1 - 08-03-2014, 04:23 PM
RE: Philco 70 Reproduction Cabinet - by morzh - 08-03-2014, 05:20 PM
RE: Philco 70 Reproduction Cabinet - by Arran - 08-04-2014, 08:32 PM
RE: Philco 70 Reproduction Cabinet - by morzh - 08-05-2014, 11:11 AM
RE: Philco 70 Reproduction Cabinet - by Arran - 08-06-2014, 01:32 AM
RE: Philco 70 Reproduction Cabinet - by morzh - 08-06-2014, 10:11 AM
RE: Philco 70 Reproduction Cabinet - by morzh - 08-06-2014, 10:35 AM
RE: Philco 70 Reproduction Cabinet - by Arran - 08-06-2014, 08:16 PM
RE: Philco 70 Reproduction Cabinet - by JimZ - 08-10-2014, 10:12 AM
RE: Philco 70 Reproduction Cabinet - by David - 08-10-2014, 11:38 AM
RE: Philco 70 Reproduction Cabinet - by morzh - 08-11-2014, 03:46 PM
RE: Philco 70 Reproduction Cabinet - by morzh - 08-11-2014, 04:03 PM
RE: Philco 70 Reproduction Cabinet - by morzh - 08-11-2014, 04:19 PM
RE: Philco 70 Reproduction Cabinet - by morzh - 08-11-2014, 09:24 PM
RE: Philco 70 Reproduction Cabinet - by tab10672 - 08-12-2014, 09:18 AM
RE: Philco 70 Reproduction Cabinet - by Arran - 08-12-2014, 10:50 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently 800 online users. [Complete List]
» 1 Member(s) | 799 Guest(s)
Avatar

>