Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

new project 48-482
#12

I am finally satisfied with my 48-482. The saga of the electronic restoration can be found in the appropriate section. I'll just say, the problem was an error on my part, a miss-wired connection of a condenser. Fixed that and the FM volume came up to what it should be. I am running this radio with just the original built in antenna, the one that has the little metal tab that wraps around the line cord. It picks up as well as any of my FM receivers now, considering the antenna, and sounds better than all but my stereo system. I can get all the local stations BOOMING in loud and clear, and some fairly distant too. Well worth all the study and effort to make this old girl sing like new again.


Messages In This Thread
new project 48-482 - by mikethedruid - 07-25-2014, 05:56 PM
RE: new project 48-482 - by klondike98 - 07-25-2014, 11:15 PM
RE: new project 48-482 - by Eric Adams - 07-26-2014, 12:10 AM
RE: new project 48-482 - by klondike98 - 07-26-2014, 08:42 AM
RE: new project 48-482 - by mikethedruid - 07-26-2014, 03:47 PM
RE: new project 48-482 - by mikethedruid - 08-05-2014, 10:05 PM
RE: new project 48-482 - by morzh - 08-05-2014, 10:44 PM
RE: new project 48-482 - by klondike98 - 08-05-2014, 11:24 PM
RE: new project 48-482 - by Eric Adams - 08-06-2014, 12:28 AM
RE: new project 48-482 - by mikethedruid - 08-06-2014, 01:13 AM
RE: new project 48-482 - by Tom Hamilton - 08-10-2014, 09:22 PM
RE: new project 48-482 - by mikethedruid - 08-19-2014, 05:35 PM
RE: new project 48-482 - by klondike98 - 08-20-2014, 11:13 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently no members online.

>