Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Found today at Goodwill
#8

Just had some excitement with the 95! It was working well until I bumped the cord and then, POW! The plug end shorted out and tripped the breaker! Cut the cord down, put on a better end and brought the unit up on the bulbs after resetting the breaker and there is no permanent harm apparent. Even so, I think I'll just replace the whole power cord as I see other spots in it I don't trust. Put me in mind of my 87 highboy when I first got it. Worked well for a week, then the plug end did a fireworks show for me one day. Oddly, that never tripped the breaker on that circuit and it had a perfect looking cord on it. I think the 95 might start my fall "Replace Those Old Cords" program. Icon_smile

No matter where you go, there you are.


Messages In This Thread
Found today at Goodwill - by Jayce - 09-07-2014, 08:47 PM
RE: Found today at Goodwill - by morzh - 09-07-2014, 08:54 PM
RE: Found today at Goodwill - by Art Hoch - 09-07-2014, 09:11 PM
RE: Found today at Goodwill - by Jayce - 09-07-2014, 09:18 PM
RE: Found today at Goodwill - by sam - 09-07-2014, 10:50 PM
RE: Found today at Goodwill - by Arran - 09-08-2014, 12:48 AM
RE: Found today at Goodwill - by David - 09-08-2014, 08:42 AM
RE: Found today at Goodwill - by Jayce - 09-08-2014, 07:44 PM
RE: Found today at Goodwill - by Ron Ramirez - 09-08-2014, 08:13 PM
RE: Found today at Goodwill - by Warren - 09-08-2014, 09:31 PM
RE: Found today at Goodwill - by Tom Hamilton - 09-09-2014, 12:43 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently 735 online users. [Complete List]
» 1 Member(s) | 734 Guest(s)
Avatar

>