Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

SW aerial
#23

Out in the work shop turned on my SX-130 to see what was out there just after 12 noon 9-19-14 was going thur the ham band on 40 meters found a net that I was able to listen to for 30-35 minutes keep fading in out every 5 minutes. The frequency was 7.251 mhz ssb. Total lost of singal around 12.40PM. My receiver is analog looked up ther frequiency on the internet. First time listening to these guys will try tomorrow just never know what you will hear. Ant 20 feet of wire about 15 feet above the ground my location 184 feet above sea level. David


Messages In This Thread
SW aerial - by fields 100 - 03-11-2014, 08:46 AM
RE: SW aerial - by morzh - 03-11-2014, 01:46 PM
RE: SW aerial - by Art Hoch - 03-11-2014, 10:04 PM
RE: SW aerial - by captainslack - 03-12-2014, 02:21 PM
RE: SW aerial - by Eric T - 03-12-2014, 08:55 PM
RE: SW aerial - by Radioroslyn - 03-13-2014, 08:18 AM
RE: SW aerial - by fields 100 - 03-13-2014, 09:01 AM
RE: SW aerial - by David - 03-13-2014, 01:42 PM
RE: SW aerial - by Radioroslyn - 03-13-2014, 05:28 PM
RE: SW aerial - by fields 100 - 03-13-2014, 06:29 PM
RE: SW aerial - by fields 100 - 09-03-2014, 09:39 AM
RE: SW aerial - by morzh - 09-03-2014, 09:48 AM
RE: SW aerial - by fields 100 - 09-03-2014, 11:42 AM
RE: SW aerial - by morzh - 09-03-2014, 11:56 AM
RE: SW aerial - by Mondial - 09-03-2014, 02:12 PM
RE: SW aerial - by David - 09-05-2014, 03:51 PM
RE: SW aerial - by David - 09-05-2014, 06:14 PM
RE: SW aerial - by fields 100 - 09-16-2014, 06:25 PM
RE: SW aerial - by David - 09-17-2014, 09:04 AM
RE: SW aerial - by PhilcoJohn - 09-17-2014, 07:44 PM
RE: SW aerial - by fields 100 - 09-17-2014, 10:01 PM
RE: SW aerial - by Mondial - 09-17-2014, 10:08 PM
RE: SW aerial - by David - 09-19-2014, 08:17 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently no members online.

>