Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Zenith consoles
#1

Good Evening All from England

This is a fabulous site and has helped me greatly in the restoration of a Philco console. My interest in American sets has now extended to Zenith consoles, of which I’ve recently acquired no fewer than four – from mid 1930’s to 1941. I’m wondering if there is a similar site to this one to help me in the task of restoring these. I’ve been looking on the internet and so far not found one. It’s always more difficult to restore sets from another continent and any advice at all would be most appreciated.

Regards
Jonathan
skodajag@aol.com


Messages In This Thread
Zenith consoles - by skodajag - 12-21-2008, 04:01 PM
Re: Zenith consoles - by BDM - 12-21-2008, 04:09 PM
Re: Zenith consoles - by Doug Houston - 12-21-2008, 10:47 PM
Re: Zenith consoles - by etech - 12-22-2008, 09:05 AM
Re: Zenith consoles - by Doug Houston - 12-22-2008, 04:49 PM
Re: Zenith consoles - by etech - 12-22-2008, 05:30 PM
Zenith Consoles part two - by skodajag - 12-22-2008, 07:29 PM
Re: Zenith consoles - by Ron Ramirez - 12-22-2008, 08:06 PM
Re: Zenith consoles - by etech - 12-22-2008, 09:17 PM
Re: Zenith consoles - by Doug Houston - 12-23-2008, 12:04 AM
Re: Zenith consoles - by skodajag - 12-26-2008, 01:37 PM
Re: Zenith consoles - by Jim Berg - 01-04-2009, 01:55 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco model 38 code 121 not receiving signal.
So one last question before I finish this radio. Regarding the speaker and output transformer. I salvaged the original o...Stormlord5500 — 09:31 AM
462ron
It’s on the bottom of the homepage of our Philcoradio.com homepage! Ron462ron — 07:20 AM
Model 70 Cabinet Trim
Steve might have some trim left. Not sure he is making anything.morzh — 06:12 AM
Model 70 Cabinet Trim
Hello musar, First all welcome to the forum and yes that is true that steve stopped making trim . Sincerely Richar...radiorich — 12:13 AM
Model 70 Cabinet Trim
I have recently come into possession of a Model 70.  The trim around the base needs to be replaced.  If this were years ...musar — 12:07 AM
philcorepairbench.com - shadow-meter
Anyone know of a way to recover these files from the repair bench? Thanks. fenbach — 11:16 PM
Philco model 38 code 121 not receiving signal.
That's true. Of course If I were to get a vtvm I'd probably have to sink money in to it to get it working right. Probabl...Stormlord5500 — 08:44 PM
Philco model 38 code 121 not receiving signal.
A DMM is good enough. One rarely has to measure indictance, but if you do, short of getting a serious LCR meter (I hav...morzh — 07:35 PM
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM

[-]
Who's Online
There are currently 525 online users. [Complete List]
» 1 Member(s) | 524 Guest(s)
Avatar

>