My Brand Z G725

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

My Brand Z G725

Ron Ramirez
Silent Key

Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand State, Province, Country: Indiana

12-25-2014, 03:45 PM

Could be...measure across the two outer terminals and see if you get anything close to the rated resistance. If not, then you have a problem.

Preferably using an analog VOM, measure between the center terminal and one of the outer terminals. Holding the test leads in place (alligator clips come in handy here), slowly turn the control from one end to the other. If the resistance does not change smoothly but jumps open here and there...then you have a problem.

--
Ron Ramirez
Ferdinand IN

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

My Brand Z G725 - by Eric Adams - 12-25-2014, 12:53 AM

RE: My Brand Z G725 - by OldRestorer - 12-25-2014, 07:42 AM

RE: My Brand Z G725 - by Ron Ramirez - 12-25-2014, 09:25 AM

RE: My Brand Z G725 - by Eric Adams - 12-25-2014, 11:19 AM

RE: My Brand Z G725 - by Ron Ramirez - 12-25-2014, 03:45 PM

RE: My Brand Z G725 - by Jayce - 12-25-2014, 04:27 PM

RE: My Brand Z G725 - by Eric Adams - 12-25-2014, 11:40 PM

RE: My Brand Z G725 - by morzh - 12-26-2014, 01:02 AM

RE: My Brand Z G725 - by Eric Adams - 12-26-2014, 01:33 AM

RE: My Brand Z G725 - by morzh - 12-26-2014, 12:46 PM

RE: My Brand Z G725 - by Eric Adams - 12-27-2014, 01:43 AM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco model 38 code 121 not receiving signal.
So what was wrong with the original speaker? Was the cone damaged? Unless it's totally hopeless I would put it aside as ...Arran — 05:31 PM
My collection presentation
There is an article on my site that introduces the first portable radios in my collection. I have only provided a link t...Vlad95 — 01:17 PM
Electrolytic restuffing/internals
Bridkarl This specific cap you have is the easiset type to restuff. I usually cut it at the upper border of the depr...morzh — 11:35 AM
philco predicta
Hi CGL18, First off, welcome to the Philco Phorum. I have not worked on a TV for a while but here are some givens: ...MrFixr55 — 08:22 AM
Another amp build - here I go again!
Sweet! I actually have a Dynaco Mark 4 that I had been running with 6L6s with no mods. Seemed to my 14-year-old head a...MrFixr55 — 12:57 AM
PT-6 finished!!
Hi Gang, Tube heaters are not "Ohmic" devices (that maintain specified resistance over wide temperature, c...MrFixr55 — 12:03 AM
Electrolytic restuffing/internals
Look here: Philco-F676-124 Vlad95 — 08:02 PM
PT-6 finished!!
Well the 35Z3 doesn't have a tap on the tube heater for a pilot light, so in this set they have the dial lamp paralleled...Arran — 06:21 PM
Electrolytic restuffing/internals
Thanks. I think I try to cut this as suggested. I don’t have a lathe, but I do have a tap and die set. I am going to see...bridkarl — 04:46 PM
Another amp build - here I go again!
Hey all! Well, I guess that with what I learned from my last build, it's time to move up the ladder another rung and tak...TV MAN — 04:38 PM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me