1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Missing 16X-126 dial mount
k9uw
Junior Member
**
Posts: 35
Threads: 12
Joined: Nov 2014
City: Amherst, WI
#3

04-10-2015, 04:37 PM
(04-10-2015, 04:15 PM)klondike98 Wrote:  If you scroll down the page of this link http://mcclellans.com/Philco16BCathedralRestoration.htm there is a photo of the front of the chassis with the dial and the metal piece that holds the dial.  Someone else may have a better photo of it, but that can give you some idea of what you're looking for I think.

Thanks, Bob!

I looked at that page and wondered if it would be the same critter.  When looking at a replica dial at RadioDaze, the number of rivet holes is right.  

Wonder how many other sets used that same part?

Mike, K9UW
Amherst, WI
Mike, K9UW
Amherst, WI
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Missing 16X-126 dial mount - by k9uw - 04-10-2015, 03:33 PM
RE: Missing 16X-126 dial mount - by klondike98 - 04-10-2015, 04:15 PM
RE: Missing 16X-126 dial mount - by k9uw - 04-10-2015, 04:37 PM
RE: Missing 16X-126 dial mount - by Ron Ramirez - 04-10-2015, 06:05 PM
RE: Missing 16X-126 dial mount - by klondike98 - 04-10-2015, 07:02 PM
RE: Missing 16X-126 dial mount - by k9uw - 04-10-2015, 07:11 PM
RE: Missing 16X-126 dial mount - by Ron Ramirez - 04-15-2015, 08:47 PM
RE: Missing 16X-126 dial mount - by k9uw - 04-15-2015, 09:07 PM
RE: Missing 16X-126 dial mount - by Ron Ramirez - 04-15-2015, 09:57 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration