Bakelite block challenge???

Register

Guest Join Us

Hello Guest,

Please feel free to join us!
There are many more parts of the Phorum that only members can see.

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Bakelite block challenge???

klondike98
Phorum Moderator

Posts: 5,170
Threads: 274
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR

#6

04-21-2015, 09:21 PM

Dan, I'm on my phone so answering this is a little cumbersome...hope ive got my info right. You have a 3650 which is the Canadian version of US 650 (schematic link). Looking at block cap #80 it does say 0.3uF That probably means the two 0.15uF caps in the block are wired in parallel to yield 0.3uF value. can you show a close up photo on the block#80?

The "U" means that pin 1 is ungrounded. I suspect that pins 2 & 3 are wired together with a jumper wire?? Which gives the 0.3uF cap value. Make sense?

[in your previous post I think you mean to have written 0.3uF and 0.15uF where you have written .03 and .05....]

Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page

« Next Oldest | Next Newest »

Messages In This Thread

Bakelite block challenge??? - by Dan Walker - 04-21-2015, 05:07 PM

RE: Bakelite block challenge??? - by radiohenry - 04-21-2015, 07:12 PM

RE: Bakelite block challenge??? - by sam - 04-21-2015, 07:16 PM

RE: Bakelite block challenge??? - by klondike98 - 04-21-2015, 07:24 PM

RE: Bakelite block challenge??? - by Dan Walker - 04-21-2015, 08:44 PM

RE: Bakelite block challenge??? - by klondike98 - 04-21-2015, 09:21 PM

RE: Bakelite block challenge??? - by Dan Walker - 04-23-2015, 09:45 AM

RE: Bakelite block challenge??? - by morzh - 04-23-2015, 10:52 AM

RE: Bakelite block challenge??? - by klondike98 - 04-23-2015, 12:29 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM

Who's Online

There are currently 1006 online users. [Complete List]
» 1 Member(s) | 1005 Guest(s)