Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 42-1012 Alignment
#16

Congratulations Icon_thumbup

Seems like more and more some mica caps are hard to assume as being good.

John KK4ZLF
Lexington, KY
"illegitimis non carborundum"


Messages In This Thread
Philco 42-1012 Alignment - by vecher - 04-22-2015, 08:40 PM
RE: Philco 42-1012 Alignment - by Radioroslyn - 04-22-2015, 09:00 PM
RE: Philco 42-1012 Alignment - by Nick3092 - 04-22-2015, 09:28 PM
RE: Philco 42-1012 Alignment - by vecher - 04-22-2015, 11:03 PM
RE: Philco 42-1012 Alignment - by vecher - 04-24-2015, 02:44 PM
RE: [b]Philco 42-1012 Alignment[/b] - by vecher - 04-25-2015, 11:16 PM
RE: Philco 42-1012 Alignment - by vecher - 04-26-2015, 04:01 PM
RE: Philco 42-1012 Alignment - by Ron Ramirez - 04-27-2015, 12:34 PM
RE: Philco 42-1012 Alignment - by klondike98 - 04-27-2015, 03:30 PM
RE: Philco 42-1012 Alignment - by Eliot Ness - 04-27-2015, 03:59 PM
RE: Philco 42-1012 Alignment - by vecher - 04-27-2015, 06:59 PM
RE: Philco 42-1012 Alignment - by Eliot Ness - 04-27-2015, 08:06 PM
RE: Philco 42-1012 Alignment - by vecher - 04-27-2015, 08:36 PM
RE: Philco 42-1012 Alignment - by vecher - 04-29-2015, 12:50 AM
RE: Philco 42-1012 Alignment - by klondike98 - 04-29-2015, 08:35 AM
RE: Philco 42-1012 Alignment - by Eliot Ness - 04-29-2015, 10:16 AM
RE: Philco 42-1012 Alignment - by Ron Ramirez - 04-29-2015, 11:08 AM
RE: Philco 42-1012 Alignment - by sleuth255 - 04-29-2015, 02:24 PM
RE: Philco 42-1012 Alignment - by codefox1 - 04-29-2015, 03:09 PM
RE: Philco 42-1012 Alignment - by vecher - 04-30-2015, 10:51 PM
RE: Philco 42-1012 Alignment - by Edisla - 05-11-2015, 11:17 AM
RE: Philco 42-1012 Alignment - by vecher - 05-11-2015, 11:27 AM
RE: Philco 42-1012 Alignment - by Edisla - 05-11-2015, 11:45 AM
RE: Philco 42-1012 Alignment - by vecher - 05-11-2015, 04:43 PM



Users browsing this thread:
[-]
Recent Posts
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM
Testing a speaker and output transformer Trutone A2-G
morzh Short-circuited turns can be considered as a half-dead transformer. But on this case transformer will hot and s...Vlad95 — 11:01 AM
Testing a speaker and output transformer Trutone A2-G
I am not sure how a transformer could be weak. It could be inadequate, but only when you replace the original with somet...morzh — 09:56 AM

[-]
Who's Online
There are currently 2138 online users. [Complete List]
» 1 Member(s) | 2137 Guest(s)
Avatar

>