42-1008P ALigntment

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

42-1008P ALigntment

Edisla
Member

Posts: 155
Threads: 25
Joined: Sep 2014
City: Folsom, CA

05-10-2015, 11:58 PM

I have the BC band aligned as good as I can get it. A tad off on the higher freq's but not to bad.

As far as the SW band goes it is a bit off.

I followed the instructions and get 15MHz dialed in but then when I go down to 10MHz to dial in WWV it actual sits around 10.2-10.3MHz

Is this normal?

Do these things never line up as good as we'd like?

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

42-1008P ALigntment - by Edisla - 05-10-2015, 11:58 PM

RE: 42-1008P ALigntment - by Warren - 05-11-2015, 12:07 AM

RE: 42-1008P ALigntment - by vecher - 05-11-2015, 09:54 AM

RE: 42-1008P ALigntment - by Edisla - 05-11-2015, 10:43 AM

RE: 42-1008P ALigntment - by vecher - 05-11-2015, 11:29 AM

RE: 42-1008P ALigntment - by Edisla - 05-11-2015, 01:25 PM

RE: 42-1008P ALigntment - by Edisla - 05-11-2015, 09:56 PM

RE: 42-1008P ALigntment - by vecher - 05-11-2015, 11:31 PM

RE: 42-1008P ALigntment - by Edisla - 05-11-2015, 11:57 PM

RE: 42-1008P ALigntment - by Edisla - 05-12-2015, 12:48 AM

RE: 42-1008P ALigntment - by Nick3092 - 05-12-2015, 10:09 AM

RE: 42-1008P ALigntment - by vecher - 05-18-2015, 11:36 PM

RE: 42-1008P ALigntment - by Edisla - 05-20-2015, 09:48 PM

RE: 42-1008P ALigntment - by Ron Ramirez - 05-20-2015, 09:59 PM

RE: 42-1008P ALigntment - by Edisla - 05-20-2015, 10:23 PM

RE: 42-1008P ALigntment - by vecher - 05-20-2015, 10:32 PM

RE: 42-1008P ALigntment - by Edisla - 05-21-2015, 11:41 AM

RE: 42-1008P ALigntment - by vecher - 05-21-2015, 09:18 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM
Testing a speaker and output transformer Trutone A2-G
morzh Short-circuited turns can be considered as a half-dead transformer. But on this case transformer will hot and s...Vlad95 — 11:01 AM
Testing a speaker and output transformer Trutone A2-G
I am not sure how a transformer could be weak. It could be inadequate, but only when you replace the original with somet...morzh — 09:56 AM

Who's Online

There are currently 2298 online users. [Complete List]
» 3 Member(s) | 2295 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me