Model 60 Tuning Condenser Shaft Slipping

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Model 60 Tuning Condenser Shaft Slipping

jayoungs
Member

Posts: 92
Threads: 18
Joined: Dec 2008

#13

01-31-2009, 05:52 PM

Hey exray,

It is all frozen up. Screw, nut neither will turn. I followed Ron's advice and have soaked it well to see if it will work loose. I have had some success, though. After 3 thorough cleanings and lithium white lube applications, I now have the shaft engaging the blades in a limited manner. I figure when I get the screw loose, lubed and adjusted, then it will work okay. I've been told I've got a screw loose a few times, for once I wish it was true.... Icon_smile

"Ignorance is bliss...'til you have to fix a radio..."

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

Model 60 Tuning Condenser Shaft Slipping - by jayoungs - 01-29-2009, 01:18 PM

Re: Model 60 Tuning Condenser Shaft Slipping - by exray - 01-29-2009, 02:37 PM

Re: Model 60 Tuning Condenser Shaft Slipping - by jayoungs - 01-29-2009, 09:36 PM

Re: Model 60 Tuning Condenser Shaft Slipping - by Chuck Schwark - 01-30-2009, 10:41 AM

Re: Model 60 Tuning Condenser Shaft Slipping - by Chuck Schwark - 01-30-2009, 01:03 PM

Re: Model 60 Tuning Condenser Shaft Slipping - by jayoungs - 01-30-2009, 10:55 PM

Re: Model 60 Tuning Condenser Shaft Slipping - by Texasrocker - 01-31-2009, 02:48 AM

Re: Model 60 Tuning Condenser Shaft Slipping - by jayoungs - 01-31-2009, 11:22 AM

Re: Model 60 Tuning Condenser Shaft Slipping - by Ron Ramirez - 01-31-2009, 11:49 AM

Re: Model 60 Tuning Condenser Shaft Slipping - by jayoungs - 01-31-2009, 12:31 PM

Re: Model 60 Tuning Condenser Shaft Slipping - by Ron Ramirez - 01-31-2009, 12:44 PM

Re: Model 60 Tuning Condenser Shaft Slipping - by exray - 01-31-2009, 02:47 PM

Re: Model 60 Tuning Condenser Shaft Slipping - by jayoungs - 01-31-2009, 05:52 PM

Re: Model 60 Tuning Condenser Shaft Slipping - by codefox1 - 01-31-2009, 09:39 PM

Re: Model 60 Tuning Condenser Shaft Slipping - by Texasrocker - 02-01-2009, 04:26 AM

Re: Model 60 Tuning Condenser Shaft Slipping - by exray - 02-01-2009, 08:26 AM

Re: Model 60 Tuning Condenser Shaft Slipping - by jayoungs - 02-04-2009, 02:23 PM

View a Printable Version

Users browsing this thread:

Recent Posts
Model 70 Cabinet Trim
Hello musar, First all welcome to the forum and yes that is true that steve stopped making trim . Sincerely Richar...radiorich — 12:13 AM
Model 70 Cabinet Trim
I have recently come into possession of a Model 70. The trim around the base needs to be replaced. If this were years ...musar — 12:07 AM
philcorepairbench.com - shadow-meter
Anyone know of a way to recover these files from the repair bench? Thanks. fenbach — 11:16 PM
Philco model 38 code 121 not receiving signal.
That's true. Of course If I were to get a vtvm I'd probably have to sink money in to it to get it working right. Probabl...Stormlord5500 — 08:44 PM
Philco model 38 code 121 not receiving signal.
A DMM is good enough. One rarely has to measure indictance, but if you do, short of getting a serious LCR meter (I hav...morzh — 07:35 PM
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM
Philco model 38 code 121 not receiving signal.
I use a pair of Mastercraft brand DMMs from Canadian Tire, from what I read most of those DMMs use the same main chip re...Arran — 02:36 PM
Philco model 38 code 121 not receiving signal.
Thank you sir. Yes I feel good and also relieved because this one's been weighing on me a bit.Stormlord5500 — 11:18 AM
Philco model 38 code 121 not receiving signal.
It feels good don't it? Good luck on the rest.Paul Philco322 — 11:06 AM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me