1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Using Gojo Creme on veneer
TA Forbes
Deviate Emeritus
*****
Posts: 2,353
Threads: 92
Joined: May 2010
City: Clayton, NC
#6

06-03-2015, 09:30 AM
"Washing" a cabinet with go-jo is a great way to remove the years of attic dirt. It gives you a better idea just what condition your cabinet is in and whether or not you want to refinish. 

I have had many cabinets that literally "came alive" after being cleaned with go-jo. 

NEVER use the go-jo with pumice on a cabinet!!
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Using Gojo Creme on veneer - by TheUniversalDave1 - 03-16-2015, 11:07 PM
RE: Using Gojo Creme on veneer - by Art Hoch - 03-17-2015, 11:29 AM
RE: Using Gojo Creme on veneer - by OldRestorer - 03-17-2015, 11:51 AM
RE: Using Gojo Creme on veneer - by sdradioman - 05-28-2015, 08:17 PM
RE: Using Gojo Creme on veneer - by TA Forbes - 06-03-2015, 09:30 AM
RE: Using Gojo Creme on veneer - by KCMike - 06-03-2015, 01:08 PM
RE: Using Gojo Creme on veneer - by klondike98 - 06-03-2015, 05:10 PM
RE: Using Gojo Creme on veneer - by Art Hoch - 06-13-2015, 06:27 PM
RE: Using Gojo Creme on veneer - by Dan Walker - 07-12-2015, 05:40 PM
RE: Using Gojo Creme on veneer - by Fred Taylor - 07-12-2015, 06:05 PM
RE: Using Gojo Creme on veneer - by sam - 07-12-2015, 06:49 PM
RE: Using Gojo Creme on veneer - by Edisla - 07-12-2015, 11:42 PM
RE: Using Gojo Creme on veneer - by Fred Taylor - 07-13-2015, 12:28 AM
RE: Using Gojo Creme on veneer - by Squire - 07-26-2015, 12:44 AM
RE: Using Gojo Creme on veneer - by Eric Adams - 07-28-2015, 11:49 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently 719 online users. [Complete List]
» 1 Member(s) | 718 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration