1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Power supply for 37-33
Radioroslyn
Phorum Expert
*****
Posts: 7,305
Threads: 270
Joined: Dec 2009
City: Roslyn Pa
#6

06-29-2015, 07:24 AM
Not sure if it will. The 37-33 requires two bias voltages  -3 and -9v. It's simple enough to wire up a battery or two for these voltages. Then all you need is +135v, 90v, and 2v for the filaments. Be sure to throttle back the filament voltage if you have been using the p/s on a set with 01A's.

Terry
ps After looking at the link it should work fine!!!
(This post was last modified: 06-29-2015, 07:29 AM by Radioroslyn.)
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Power supply for 37-33 - by KLBowers - 06-26-2015, 08:31 AM
RE: Power supply for 37-33 - by sam - 06-26-2015, 12:03 PM
RE: Power supply for 37-33 - by KLBowers - 06-26-2015, 01:19 PM
RE: Power supply for 37-33 - by klondike98 - 06-26-2015, 03:01 PM
RE: Power supply for 37-33 - by KLBowers - 06-29-2015, 06:57 AM
RE: Power supply for 37-33 - by Radioroslyn - 06-29-2015, 07:24 AM
RE: Power supply for 37-33 - by KLBowers - 06-29-2015, 07:31 AM
RE: Power supply for 37-33 - by Radioroslyn - 06-29-2015, 03:44 PM
RE: Power supply for 37-33 - by KLBowers - 06-29-2015, 10:32 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco Model 38-7: what caps & resistors do fail typically?
Since you stated earlier, you have a console 38-7XX.  They also had a 38-7T (table), and 38-7CS (chairside).  A very nic...GarySP — 01:18 PM
Part numbers to model cross
That I wouldn't know, but sometimes the radio document itself shows one, same as the capacitor cans' etc pinouts.morzh — 12:46 PM
Part numbers to model cross
Thank you morzh, that is exactly what I was looking for. Now , is there some where that shows pinouts for Philco power ...Jim Dutridge — 11:37 AM
Restoration of the Canadian General Electric A-87
Thanks for your help Michael. In fact, this video is only an intermediate result. Later I had to apply another tinting l...RadioSvit — 09:01 AM
Restoration of the Canadian General Electric A-87
Great job on the cabinet. PS. In the US notation, "kenotron" refers to specific type of tubes; we call re...morzh — 08:24 AM
Part numbers to model cross
This document has at least some tables of models and parts used. Example: Choke 32-7572, used in 604 radio. Search f...morzh — 08:19 AM
Restoration of the Canadian General Electric A-87
I also checked all the radio tubes on my Hickok 530 tube tester. The 5Z3 kenotron turned out to be faulty, all the other...RadioSvit — 08:02 AM
Restoration of the Canadian General Electric A-87
Well... While the varnish is drying up, I started repairing the chassis... Of course I started by replacing the pa...RadioSvit — 07:12 AM
Philco Model 38-7: what caps & resistors do fail typically?
Hello Martin, Welcome aboard our little community what great Model 38-7 Sincerely Richardradiorich — 12:30 AM
Philco Model 38-7: what caps & resistors do fail typically?
Welcome to the Phorum Martin. I count about 9 paper caps, the 3 electrolytic caps and 2-Y2 safety caps to replace th...RodB — 09:44 PM

[-]
Who's Online
There are currently 1497 online users. [Complete List]
» 1 Member(s) | 1496 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios