1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Model 96 Field coil.....
Jim Koehler
Junior Member
**
Posts: 44
Threads: 4
Joined: Dec 2013
City: Freeport, LI, NY
#1

07-01-2015, 02:54 PM
Hi Guys......

On the bench is a model 96 and I'm having a few issues....

Is there a list for the resistor values?  Other than part numbers and Bintliff's Philco Cap Guide Pt. II, I was just wondering if a Philco list can be found.

Can someone furnish me with the resistance value of the field coil?  Mine's reading about 2,200 ohms DC. On a test, I had 334 VDC going into the FC and 150 VDC coming out. It should be about 225 VDC. Monitoring the amp draw of the radio, it's around 800 ma. I think this coil is shorted but knowing the actual resistance value would be a big help. (the cap can (p/n 3754) has been recapped and works fine. 

Tnx...
...Jim
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Model 96 Field coil..... - by Jim Koehler - 07-01-2015, 02:54 PM
RE: Model 96 Field coil..... - by morzh - 07-01-2015, 03:01 PM
RE: Model 96 Field coil..... - by Jim Koehler - 07-01-2015, 04:02 PM
RE: Model 96 Field coil..... - by morzh - 07-01-2015, 04:14 PM
RE: Model 96 Field coil..... - by Radioroslyn - 07-01-2015, 04:40 PM
RE: Model 96 Field coil..... - by morzh - 07-01-2015, 04:46 PM
RE: Model 96 Field coil..... - by codefox1 - 07-01-2015, 05:28 PM
RE: Model 96 Field coil..... - by Ron Ramirez - 07-01-2015, 07:54 PM
RE: Model 96 Field coil..... - by Radioroslyn - 07-01-2015, 08:36 PM
RE: Model 96 Field coil..... - by Jim Koehler - 07-01-2015, 08:47 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM
Testing a speaker and output transformer Trutone A2-G
morzh Short-circuited turns can be considered as a half-dead transformer. But on this case transformer will hot and s...Vlad95 — 11:01 AM
Testing a speaker and output transformer Trutone A2-G
I am not sure how a transformer could be weak. It could be inadequate, but only when you replace the original with somet...morzh — 09:56 AM

[-]
Who's Online
There are currently 2212 online users. [Complete List]
» 2 Member(s) | 2210 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration