Philco 20 delux

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Philco 20 delux

gary rabbitt
Senior Member

Posts: 271
Threads: 12
Joined: Nov 2005
City: Nashville, TN

02-18-2009, 03:17 PM

Hey RIch,
Here's the photos of how I did the filter can. As you can see, I didn't have to remove any tar at all.
The bottom piece slips right off, it's not soldered or anything.

The paint color of the filter can is a little off. I think it was a darker color on the metal itself, very thin like an anodizing finish. As it was slightly rusted, I used Krylon drab camo color for now.
Good luck,
Gary.
[Image: http://i465.photobucket.com/albums/rr19/...C00075.jpg]
[Image: http://i465.photobucket.com/albums/rr19/...C00076.jpg]
[Image: http://i465.photobucket.com/albums/rr19/...C00077.jpg]

[Image: http://i465.photobucket.com/albums/rr19/...C00078.jpg]

[Image: http://i465.photobucket.com/albums/rr19/...C00079.jpg]

[Image: http://i465.photobucket.com/albums/rr19/...C00080.jpg]

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

Philco 20 delux - by radiorich - 02-05-2009, 05:25 PM

Re: Philco 20 delux - by Arran - 02-05-2009, 07:20 PM

Re: Philco 20 deluxe - by radiorich - 02-05-2009, 08:27 PM

Re: Philco 20 delux - by Arran - 02-05-2009, 10:36 PM

Re: Philco 20 delux - by radiorich - 02-08-2009, 09:31 PM

Re: Philco 20 delux - by gary rabbitt - 02-17-2009, 09:40 PM

Re: Philco 20 delux - by radiorich - 02-18-2009, 03:14 AM

Re: Philco 20 delux - by gary rabbitt - 02-18-2009, 03:17 PM

Re: Philco 20 delux - by radiorich - 02-18-2009, 04:11 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me