Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

This was a hard decision...for me anyhow
#1

The Wisconsin Antique Radio Club swap meet was today, and despite the beautiful weather, vendor turn out was meager. I was just getting ready to leave when I saw a late comer just setting up and spotted this:

   

A 38-116. I asked the out-of-breath guy who just unloaded it from his van how much. He said $30. Wow....this seems to good to be true. Closer examination revealed a cabinet that needed total refinishing (my picture doesn't show the wear, dings, scratches, stains, etc.). I got to talking with him a little and said "At that price you basically are just looking to free up some space?" He said yes. I pressed on. "Has anyone started to restore this or has it been sitting for years?". "I started restoring it about 20 years ago". Hmmm...now it's getting clearer. I said "Did you run into some problems?" Yes came the response. "I recapped it but couldn't get very many stations back then and only at low volume. I just tried it again today and got nothing". So basically I got the sense that he messed something up and just left it sit. As much as I would like one of these, I'm afraid I would've been biting off more than I could chew. Even an original unmolested set is a challenge to restore. Coupled with that... miles of crumbling rubber covered wire (if only this was a 1937 or earlier). In the end, I decided against it. Another guy was going to trade him a 10 year old stereo system for it, so I knew he just wanted it out of the house. I wound up coming home with a Crosley "dashboard" table model instead.

Greg V.
West Bend, WI
Member WARCI.org





Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Restoration of the Canadian General Electric A-87
Thanks for your help Michael. In fact, this video is only an intermediate result. Later I had to apply another tinting l...RadioSvit — 09:01 AM
Restoration of the Canadian General Electric A-87
Great job on the cabinet. PS. In the US notation, "kenotron" refers to specific type of tubes; we call re...morzh — 08:24 AM
Part numbers to model cross
This document has at least some tables of models and parts used. Example: Choke 32-7572, used in 604 radio. Search f...morzh — 08:19 AM
Restoration of the Canadian General Electric A-87
I also checked all the radio tubes on my Hickok 530 tube tester. The 5Z3 kenotron turned out to be faulty, all the other...RadioSvit — 08:02 AM
Restoration of the Canadian General Electric A-87
Well... While the varnish is drying up, I started repairing the chassis... Of course I started by replacing the pa...RadioSvit — 07:12 AM
Philco Model 38-7: what caps & resistors do fail typically?
Hello Martin, Welcome aboard our little community what great Model 38-7 Sincerely Richardradiorich — 12:30 AM
Philco Model 38-7: what caps & resistors do fail typically?
Welcome to the Phorum Martin. I count about 9 paper caps, the 3 electrolytic caps and 2-Y2 safety caps to replace th...RodB — 09:44 PM
Part numbers to model cross
Jim, We have this index put together by Dale Cook but I don't think that is quite what you are looking for. The Parts...klondike98 — 09:37 PM
Philco Model 38-7: what caps & resistors do fail typically?
Yep the dim bulb test is OK but I'd definitely replace all those electrolytics before I did it. Since those #47 conden...klondike98 — 09:18 PM
Philco 42-345 Restoration/Repair
The resistor is a 2.2 Meg, it was the last one I hadn't replaced. The broadcast is coming in after replacing it.osanders0311 — 09:09 PM

[-]
Who's Online
There are currently 998 online users. [Complete List]
» 1 Member(s) | 997 Guest(s)
Avatar

>