Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

FOMOCO Radio
#15

(09-12-2015, 04:20 PM)unit91 Wrote:  
(09-11-2015, 07:14 PM)VntgRads Wrote:  Find an old car antenna and give it a try.  You won't get too much of anything without one.  You may also have to adjust the antenna trimmer screw on the side.

Craig R.

OK.  When I connect the bulb wire to positive it now lights (had a bad ground before).  When I connect the radio and the bulb wires to positive at the same time the bulb goes out and the radio wire sparks.

Moved car outside to an open area and hooked up the radio to power, speakers and antenna.  While searching for a station I found one but couldn't find it again.  I turned a small screw located below the tuning button all over the place and kept trying to find that station again, but never did.


Messages In This Thread
FOMOCO Radio - by unit91 - 09-08-2015, 02:14 PM
RE: FOMOCO Radio - by VntgRads - 09-08-2015, 05:07 PM
RE: FOMOCO Radio - by unit91 - 09-09-2015, 01:39 PM
RE: FOMOCO Radio - by VntgRads - 09-09-2015, 01:47 PM
RE: FOMOCO Radio - by klondike98 - 09-09-2015, 03:26 PM
RE: FOMOCO Radio - by unit91 - 09-09-2015, 07:39 PM
RE: FOMOCO Radio - by VntgRads - 09-09-2015, 08:55 PM
RE: FOMOCO Radio - by unit91 - 09-10-2015, 08:07 PM
RE: FOMOCO Radio - by VntgRads - 09-10-2015, 09:49 PM
RE: FOMOCO Radio - by unit91 - 09-11-2015, 01:40 PM
RE: FOMOCO Radio - by VntgRads - 09-11-2015, 07:14 PM
RE: FOMOCO Radio - by unit91 - 09-12-2015, 04:20 PM
RE: FOMOCO Radio - by unit91 - 09-14-2015, 01:23 PM
RE: FOMOCO Radio - by unit91 - 09-12-2015, 03:47 PM
RE: FOMOCO Radio - by VntgRads - 09-12-2015, 05:48 PM
RE: FOMOCO Radio - by VntgRads - 09-14-2015, 02:12 PM
RE: FOMOCO Radio - by unit91 - 09-14-2015, 04:44 PM
RE: FOMOCO Radio - by VntgRads - 09-14-2015, 06:44 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently no members online.

>