Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Help with a Philco 89B
#29

I'm pretty sure I was supposed to post a power-up video quite some time back... here it finally is Icon_smile

https://youtu.be/FJ6AfDRtgbw

There are no personal problems that can't be overcome with the liberal application of high explosives


Messages In This Thread
Help with a Philco 89B - by kiwi_steve - 07-26-2015, 03:07 PM
RE: Help with a Philco 89B - by kiwi_steve - 07-26-2015, 03:34 PM
RE: Help with a Philco 89B - by Steve Davis - 07-26-2015, 05:11 PM
RE: Help with a Philco 89B - by morzh - 07-26-2015, 09:54 PM
RE: Help with a Philco 89B - by klondike98 - 07-26-2015, 10:02 PM
RE: Help with a Philco 89B - by kiwi_steve - 07-27-2015, 07:44 AM
RE: Help with a Philco 89B - by kiwi_steve - 07-27-2015, 07:59 AM
RE: Help with a Philco 89B - by morzh - 07-27-2015, 10:44 AM
RE: Help with a Philco 89B - by kiwi_steve - 07-27-2015, 02:33 PM
RE: Help with a Philco 89B - by kiwi_steve - 07-27-2015, 02:40 PM
RE: Help with a Philco 89B - by morzh - 07-27-2015, 03:14 PM
RE: Help with a Philco 89B - by kiwi_steve - 07-27-2015, 05:42 PM
RE: Help with a Philco 89B - by kiwi_steve - 07-28-2015, 02:51 AM
RE: Help with a Philco 89B - by sam - 07-28-2015, 03:00 AM
RE: Help with a Philco 89B - by kiwi_steve - 07-28-2015, 05:18 AM
RE: Help with a Philco 89B - by morzh - 07-28-2015, 09:49 AM
RE: Help with a Philco 89B - by kiwi_steve - 07-29-2015, 08:06 AM
RE: Help with a Philco 89B - by GarySP - 07-29-2015, 08:35 AM
RE: Help with a Philco 89B - by kiwi_steve - 07-29-2015, 05:10 PM
RE: Help with a Philco 89B - by kiwi_steve - 08-01-2015, 07:48 PM
RE: Help with a Philco 89B - by kiwi_steve - 08-30-2015, 12:16 AM
RE: Help with a Philco 89B - by kiwi_steve - 08-30-2015, 01:11 AM
RE: Help with a Philco 89B - by kiwi_steve - 08-30-2015, 02:27 AM
RE: Help with a Philco 89B - by kiwi_steve - 08-30-2015, 08:54 PM
RE: Help with a Philco 89B - by kiwi_steve - 09-02-2015, 06:39 PM
RE: Help with a Philco 89B - by Arran - 09-03-2015, 01:03 AM
RE: Help with a Philco 89B - by kiwi_steve - 09-03-2015, 04:28 PM
RE: Help with a Philco 89B - by kiwi_steve - 09-22-2015, 05:18 PM
RE: Help with a Philco 89B - by kiwi_steve - 10-20-2015, 12:19 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM
Testing a speaker and output transformer Trutone A2-G
morzh Short-circuited turns can be considered as a half-dead transformer. But on this case transformer will hot and s...Vlad95 — 11:01 AM
Testing a speaker and output transformer Trutone A2-G
I am not sure how a transformer could be weak. It could be inadequate, but only when you replace the original with somet...morzh — 09:56 AM

[-]
Who's Online
There are currently 2096 online users. [Complete List]
» 3 Member(s) | 2093 Guest(s)
AvatarAvatarAvatar

>