Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

My Philco 38-116
#16

Arran, you are correct, I just like the right tubes in there. All glass. This radio was originally as you know set up with glass. Can't see them much with the shields on but the one I'm working on is missing the shield bases for the mag tuner 6J5s. Still stuck in glass and seems to do find. I like the glow. This chassis had one shield cut down due to the lower seat of the metal tube. I hated that. I had a proper shield and repaced the dang metal tube with glass. Threw away the cutdown shield, if the person who did the change would have just extended the grid wire it wouldn't have been so bad.
Jerry

A friend in need is a pest!  Bill Slee ca 1970.
#17

On the other end of the spectrum from the 38-116, my RCA 15K came out with and uses all metal tubes except the eye tube. Where even I prefer glass, I wasn't happy until I found my NOS metal 6L6 tube to replace the single glass 6L6 someone had put in the radio years before. Oddly, the new military surplus metal tube I put in was almost an exact match to the original RCA metal 6L6 in there when I tested it.

No matter where you go, there you are.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Restoration of the Canadian General Electric A-87
Well... The console body has been restored, while the varnish dries reliably I started to paint the chassis ...RadioSvit — 07:12 AM
Philco Model 38-7: what caps & resistors do fail typically?
Hello Martin, Welcome aboard our little community what great Model 38-7 Sincerely Richardradiorich — 12:30 AM
Philco Model 38-7: what caps & resistors do fail typically?
Welcome to the Phorum Martin. I count about 9 paper caps, the 3 electrolytic caps and 2-Y2 safety caps to replace th...RodB — 09:44 PM
Part numbers to model cross
Jim, We have this index put together by Dale Cook but I don't think that is quite what you are looking for. The Parts...klondike98 — 09:37 PM
Philco Model 38-7: what caps & resistors do fail typically?
Yep the dim bulb test is OK but I'd definitely replace all those electrolytics before I did it. Since those #47 conden...klondike98 — 09:18 PM
Philco 42-345 Restoration/Repair
The resistor is a 2.2 Meg, it was the last one I hadn't replaced. The broadcast is coming in after replacing it.osanders0311 — 09:09 PM
Philco 42-345 Restoration/Repair
What does the resistor measure? I think it should be 3.3 Meg. If the oscillator coil has continuity and the resistanc...RodB — 09:03 PM
Philco Model 38-7: what caps & resistors do fail typically?
Good idea to check the coils... then I'll get hold of an incadescent light bulb and see what happens when the unit is sw...Musaeum — 08:49 PM
Philco 42-345 Restoration/Repair
I have that same set, ain't too much shortwave I like anyway.....it is a good AM DX set. PaulPaul Philco322 — 08:32 PM
Philco Model 38-7: what caps & resistors do fail typically?
Welcome to the Phorum, Martin! Open a new thread in Philco Electronic Restoration when you begin working on your 38-7. ...GarySP — 08:28 PM

[-]
Who's Online
There are currently 840 online users. [Complete List]
» 3 Member(s) | 837 Guest(s)
AvatarAvatarAvatar

>