Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Scott Philharmonic
#31

Been playing this radio for many months now. It produced a bit of static periodically so i finally decided to see if I could find the cause. As mentioned previously, this radio had been worked on previously. I restuffed all of the original caps that remained, leaving several older Solar Sealdtite and a couple of Sprague Black Beauties that had been replaced many years ago. I replaced all of those. Unfortunately, I had nothing to restuff to make it look original. So now there are quite a few of the beauteous Chinese yellow caps under there! It has been playing for several hours now with no hint of static. Can't trust any cap (except mica) that's over a few decades old. I guess the the Solar company went out of business in about 1949, making the solar caps in this radio at least 60 years old. Evidently huge inventories at the time found their way into the inventory of parts suppliers and were being sold well into the '70's as new caps. Little doubt that is where these came from. All capacitors and a few resistors have now been changed in this radio.
#32

Rob

Have you cleaned the tuning cap?

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#33

Yes I did, Mike. No problem there. Still no static since I replaced the Solar's. I suspect that one of those or the Black Beauties were the culprits.




Users browsing this thread:
[-]
Recent Posts
philcorepairbench.com - shadow-meter
Anyone know of a way to recover these files from the repair bench? Thanks. fenbach — 11:16 PM
Philco model 38 code 121 not receiving signal.
That's true. Of course If I were to get a vtvm I'd probably have to sink money in to it to get it working right. Probabl...Stormlord5500 — 08:44 PM
Philco model 38 code 121 not receiving signal.
A DMM is good enough. One rarely has to measure indictance, but if you do, short of getting a serious LCR meter (I hav...morzh — 07:35 PM
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM
Philco model 38 code 121 not receiving signal.
I use a pair of Mastercraft brand DMMs from Canadian Tire, from what I read most of those DMMs use the same main chip re...Arran — 02:36 PM
Philco model 38 code 121 not receiving signal.
Thank you sir. Yes I feel good and also relieved because this one's been weighing on me a bit.Stormlord5500 — 11:18 AM
Philco model 38 code 121 not receiving signal.
It feels good don't it? Good luck on the rest.Paul Philco322 — 11:06 AM
Philco model 38 code 121 not receiving signal.
I've reinstalled the coil. Now IT'S ALIVE!!!!!! I fired up my TinySA on signal generator mode and set it to 1400Kc and ...Stormlord5500 — 11:01 AM
Philco model 38 code 121 not receiving signal.
Yes, Walmart, right up there with Fluke.RodB — 11:00 AM

[-]
Who's Online
There are currently 2350 online users. [Complete List]
» 2 Member(s) | 2348 Guest(s)
AvatarAvatar

>