Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

ID of Philco's
#1

All, Here are 3 pictures of some Philco radios. I cannot find a model number on any. Can someone please ID ?

Thanks

Skip...

[Image: http://i292.photobucket.com/albums/mm38/...bhzoyl.jpg]

[Image: http://i292.photobucket.com/albums/mm38/...snhlof.jpg]

[Image: http://i292.photobucket.com/albums/mm38/...lc6f1i.jpg]

Found at antique store..
#2

Alll 3 are post war sets. 46-1201, or so, 47-1230, and a 46-350. You can find them here  http://philcoradio.com/gallery/#list

Terry
#3

Terry, Ok thanks.. the one looked closer to a 46-1209 ..
instead of a 47-1230..


Skip...
#4

 The first set could also be a 48-1201, which was the same set but with some miniature tubes, and slug tuned IF cans, I believe that the B+ voltage was higher as well.

http://www.philcoradio.com/gallery/1948a.htm#w

 The console is a 46-1209 and the last set is a 46-350, unless it has an imitation alligator covering then it would be a 48-360.
Regards
Arran
#5

All, Ok thanks.. Just a quick Question.. What are these worth.. Consider them Not working..

So I know what to offer..

Skip...
#6

All, Ok picked up all three radios for 25.00 each.. Cabinets are not in great shape. But radio itself looks OK.. Will not know until I start to pull apart.. Parts are probably worth what I paid..

Thanks
to ALL

Skip...




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently no members online.

>