Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Kirk's Sparton 65
#16

ya mike you tell him.   grab another beer anyway.   Icon_twisted

Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2
#17

Can't right now, I'm at work and we have a dry policy here. But come the evening...... Icon_smile

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#18

Changed a few resistors. Some factory that do not agree with the sch, I left them, but those 500K that show 800K I replaced. One of them was AVC.
One was the detector amp load, after which the gain went up, now much louder.
But: though the speech is fine, the music is distorted, though it is only on the local station that is very strong, and others do not play any music.

I tried a different speaker, and changed every single tube, no change.

Replaced the diode with the 8.2uF cap after I lost the 43 tube and I only had one left, so I decided, it is cleaner and the tubes are not stressed anymore.

Plenty of stations on the BC, just one on the SW, but then thd antenna is short and it's not the night yet.
If the music keeps doing that (and it seems all is good electrically) I'll just leave it be.

I'll align it one more time, see if there's any change, though it seems the trimmers that dud not do anything still don't. Strange as the 456Khz seems go through well. Bad trimmers? Could be.....

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#19

Sounds like you actually had to do some work... Icon_lol
Another 30 hours and you will know what it's like to do a cabinet...
As long as it is safe to use and sounds clear I am happy...

Icon_smile

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#20

Safe to use.... None of these are safe to use. This one has an actual hot chassis.

This is one of the worst radios I've seen. It has internally mounted IF xfmrs instead of having them on top like everyone else does. These xfmrs are huge and block access to about 1/3 of the places I'd like to acess. Horrible. When are you going to start buying normal conventional radios like some normal people, for a change? Icon_twisted

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#21

He said normal people   Icon_lol

Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2
#22

I'm not normal? Icon_crazy
Hmmm, 
 Maybe I'll have you do my Radiola 33. You like tar blocks right? or is it rosin? Icon_twisted
ooh and the 37-650 console chassis that Terry gave me... or maybe the 37-675 and the 23X... or the 37-116. Icon_twisted

Icon_smile

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#23

Easy, boy! Or I'll have you do my consoles. Of which I have quite a few. Though none of them are in the condition you like to buy yours in. Icon_lol
And....isn't the 33 filled with rosin? We can melt that out and sell. That's lifetime supply for someone who likes to solder or to play violin.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#24

What is a violine?  Icon_razz

Consoles would be 4 chassis each.  Icon_twisted
 I cant handle them anyway with my current conditions..
Enjoy your little vacation but don't forget that smoking Philco 610? 620?  Icon_lol
Get it the patch  Icon_mrgreen

Icon_smile

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#25

That will have to be after Kutztown. I'll look at it, but if it got lung cancer after that much smoking, I am no thaumaturgist.

Violine is a very deep violet color. Some violines make one feel that instead of blue.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#26

Icon_lol
You so looked that up...

I am trying to get the cabinets done but the lacquer would not be cured enough to bring to Kutztown anyway...

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#27

Yes I did. Live and learne. (No go and look up "learne").

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#28

Mike;
  RCA Nipperettes, along with their G.E and Westinghouse clones are like that, two big IF cans under the chassis, attached to the inside of the rear apron to be exact. If you want to get at the bottoms of two or three tube sockets you have to remove them. I haven't run into that under the chassis IF problem on any of my Sparton sets yet, but then again Sparton of Canada did their own thing much like other Canadian branches of U.S companies. Are they mounted, cans and all, under the chassis, or just the coils and trimmers? Maybe the trimmers are open circuit in one of the IFs?
Regards
Arran
#29

Arran, they are ca s, small ones.

I think it is a screwup in the procedure.

http://www.nostalgiaair.org/Resources/866/M0018866.htm

The C1 and C2 said in the procedure to be IF caps do not affect IF.. Nor are they have the ref designators according to the schematic. Only C3, which is, same as C2, is a dual trimmer, acts as IF.
But. C2 pair does affect the reception, both of them. I was lazy to trace them and see what they are in reality, the radio just doesn't want me to do it, too many things to unsolder and pull to see wires. And when I, without realizing that C1 has the screw with the cap inside and the screwdriver slot outside and turned it enouh so it fell inside....I spent an hour and eventually had to unsolder top two wires to get it out and put the screw back in.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#30

Hmm, very interesting, three stages of IF and two IF amps, it should be a pretty good performer once it's working right, selective as well. 
Regards
Arran




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
462ron
It’s on the bottom of the homepage of our Philcoradio.com homepage! Ron462ron — 07:20 AM
Model 70 Cabinet Trim
Steve might have some trim left. Not sure he is making anything.morzh — 06:12 AM
Model 70 Cabinet Trim
Hello musar, First all welcome to the forum and yes that is true that steve stopped making trim . Sincerely Richar...radiorich — 12:13 AM
Model 70 Cabinet Trim
I have recently come into possession of a Model 70.  The trim around the base needs to be replaced.  If this were years ...musar — 12:07 AM
philcorepairbench.com - shadow-meter
Anyone know of a way to recover these files from the repair bench? Thanks. fenbach — 11:16 PM
Philco model 38 code 121 not receiving signal.
That's true. Of course If I were to get a vtvm I'd probably have to sink money in to it to get it working right. Probabl...Stormlord5500 — 08:44 PM
Philco model 38 code 121 not receiving signal.
A DMM is good enough. One rarely has to measure indictance, but if you do, short of getting a serious LCR meter (I hav...morzh — 07:35 PM
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM
Philco model 38 code 121 not receiving signal.
I use a pair of Mastercraft brand DMMs from Canadian Tire, from what I read most of those DMMs use the same main chip re...Arran — 02:36 PM

[-]
Who's Online
There are currently 329 online users. [Complete List]
» 1 Member(s) | 328 Guest(s)
Avatar

>