1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Test Equipment

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
EICO 360 Sig generator and sweeper
vecher
Phorum Expert
*****
Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale State, Province, Country: PA
#1

12-13-2017, 02:10 PM
Can anyone tell me how to calibrate this? I cannot seem to find calibration instructions anywhere..

Thanks
Skip...
Find
morzh
Odobenus rosmarus
******
Posts: 16,507
Threads: 572
Joined: Oct 2011
City: Jackson State, Province, Country: NJ
#2

12-13-2017, 02:25 PM
Usually when calibrating an oscillator one needs a calibrated counter of the precision higher than that of the DUC.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Find
Warren
Senior Member
****
Posts: 736
Threads: 26
Joined: Jun 2013
City: Hayward, California
#3

12-13-2017, 02:32 PM
Looks like there is a manual on ebay.... https://www.ebay.com/i/263381568918?chn=...1902804856
Find
vecher
Phorum Expert
*****
Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale State, Province, Country: PA
#4

12-13-2017, 07:47 PM
I have the manual.. No instructions in it on Calibration..

It does seen to work OK Just wanted to get the frequencies to Track with dial IF possible..

Skip...
Find
Phlogiston
Radio-Fixer-Upper
*****
Posts: 2,118
Threads: 112
Joined: Jun 2010
City: Medford OR (OR what?)
#5

12-15-2017, 04:57 PM
I think if you want it to be really accurate you need the 10.7mhz xtal.
"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
Website Find
« Next Oldest | Next Newest »
Thread Closed




Users browsing this thread:
[-]
Recent Posts
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM
Testing a speaker and output transformer Trutone A2-G
morzh Short-circuited turns can be considered as a half-dead transformer. But on this case transformer will hot and s...Vlad95 — 11:01 AM
Testing a speaker and output transformer Trutone A2-G
I am not sure how a transformer could be weak. It could be inadequate, but only when you replace the original with somet...morzh — 09:56 AM

[-]
Who's Online
There are currently 2258 online users. [Complete List]
» 2 Member(s) | 2256 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Test Equipment