Posts: 1,199
Threads: 49
Joined: Oct 2017
City: Allendale, MI
Posts: 1,199
Threads: 49
Joined: Oct 2017
City: Allendale, MI
Posts: 2,118
Threads: 112
Joined: Jun 2010
City: Medford OR (OR what?)
That is quite a cabinet. The finish appears to have yellowed. If it were to be refinished it would look amazing, BUT, it is also too nice to refinish. It is possible that the hand-cleaner method might help remove some of the "yellow".
"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
(This post was last modified: 12-12-2018, 11:57 AM by Phlogiston.)
Posts: 1,199
Threads: 49
Joined: Oct 2017
City: Allendale, MI
Russ, at some point in it's history, someone tried to "restore" the finish. If you look at the edge of the door, you can see where something was wiped on and slightly spread over onto the inside surface of the door. There is evidence of this in multiple places. Perhaps you are familiar with what might have been used??? The inside of the doors and the speaker grill have a very strange color and are probably the original, deteriorated finish. The inside of the record player compartment is probably close to the original walnut color on the cabinet. Much more brown. Looking at the inside of the doors and the grille, what kind of finish would have deteriorated in that way? It looks highly oxidized and almost greenish in color. Could they have used shellac instead of lacquer? Does shellac age in that way?
It looks quite nice just sitting there and I may just leave it. It would be a lot of work to refinish and, perhaps, beyond my skill level. I would probably send it to a local pro who does a lot of refinishing of locally made, fine furniture from the earlier part of last century during Grand Rapid's heyday of furniture manufacturing. My Grebe cabinet was made by the same comapny - Berkey and Gay. I just recently discovered that quite by accident and that added to my interest in the Grebe and in this Balkeit. I like the local history, even if the radios themselves were made elsewhere and may be of questionable performance. Interstingly, I would say Berkey and Gay built the Grebe cabinet down to a price as I didn't think the construction was all that high a quality. The Balkeit seems to be a much finer cabinet. For me, it may be worth spend the $$$ on getting it refinished just for my personal satisfaction. I'm thinking out loud here and convincing myself to have it refinished!
Posts: 2,118
Threads: 112
Joined: Jun 2010
City: Medford OR (OR what?)
Yes, shellac can turn black, green or white with age and moisture but so can lacquer.
Here is a Wurlitzer that turned white:
Your radio could have been finished in shellac or lacquer. It looks like somebody tried to brighten up the yellowed finish. This would be justification (for me) to refinish it. It will be an awesome cabinet if done properly. You can test for shellac in a hidden area by applying alcohol on a rag to see if the old finish will dissolve and lacquer thinner to see if that "top coat" is poly which will get soft, but not wipe off. Hope it is not poly.
Be careful with the solvents.
"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
Posts: 1,199
Threads: 49
Joined: Oct 2017
City: Allendale, MI
Boy, I hope it's not poly as well! I may test it as you suggested.
Posts: 4,950
Threads: 54
Joined: Sep 2008
City: Sandwick, BC, CA
I was looking at an old catalog from the early 1930s, and they had a number of sets with cabinets made by Berkey and Gay Furniture, one of the makes was something called a "Cadillac" which I have never heard of, it may have been a private label brand, or the mail order outfit may have assembled them using surplus chassis installed into B&G cabinets. Balkeit was one of the larger independents started in the 1920s, whom had a few good years during the radio boom, then slowly faded, then went bust or merged into another firm.
Regards
Arran
Users browsing this thread: 1 Guest(s)
|
Recent Posts
|
Philco Model 38-7: what caps & resistors do fail typically?
|
Since you stated earlier, you have a console 38-7XX. They also had a 38-7T (table), and 38-7CS (chairside). A very nic...GarySP — 01:18 PM |
Part numbers to model cross
|
That I wouldn't know, but sometimes the radio document itself shows one, same as the capacitor cans' etc pinouts.morzh — 12:46 PM |
Part numbers to model cross
|
Thank you morzh, that is exactly what I was looking for. Now , is there some where that shows pinouts for Philco power ...Jim Dutridge — 11:37 AM |
Restoration of the Canadian General Electric A-87
|
Thanks for your help Michael. In fact, this video is only an intermediate result. Later I had to apply another tinting l...RadioSvit — 09:01 AM |
Restoration of the Canadian General Electric A-87
|
Great job on the cabinet.
PS. In the US notation, "kenotron" refers to specific type of tubes; we call re...morzh — 08:24 AM |
Part numbers to model cross
|
This document has at least some tables of models and parts used.
Example: Choke 32-7572, used in 604 radio.
Search f...morzh — 08:19 AM |
Restoration of the Canadian General Electric A-87
|
I also checked all the radio tubes on my Hickok 530 tube tester. The 5Z3 kenotron turned out to be faulty, all the other...RadioSvit — 08:02 AM |
Restoration of the Canadian General Electric A-87
|
Well... While the varnish is drying up, I started repairing the chassis...
Of course I started by replacing the pa...RadioSvit — 07:12 AM |
Philco Model 38-7: what caps & resistors do fail typically?
|
Hello Martin,
Welcome aboard our little community what great Model 38-7
Sincerely Richardradiorich — 12:30 AM |
Philco Model 38-7: what caps & resistors do fail typically?
|
Welcome to the Phorum Martin.
I count about 9 paper caps, the 3 electrolytic caps and 2-Y2 safety caps to replace th...RodB — 09:44 PM |
Who's Online
|
There are currently 1301 online users. [Complete List] » 1 Member(s) | 1300 Guest(s)
|
|
|

|