1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
PT-43 reception question
Guest
Unregistered
 
#1

02-17-2006, 10:26 PM
Hello Folks,
Well, I just recapped this little one and it plays very well with outstanding AM reception! So here's the question - I know that this SW section (1.5>2.5) is pretty much history, but when you throw the switch on the back to the police section it sounds like a switch was made but it continues to recieve AM. Any idea why? The switch appears to be wired correctly, unless I'm missing something.
Jim
Steve Chambers
Member
***
Posts: 80
Threads: 10
Joined: Sep 2005
City: Warren, Ohio
#2

02-17-2006, 11:31 PM
Well, from 1500 KHZ to 1710 is part of today's broadcast band. There will be lots of AM stations in this part of your "police" band. The rest should be pretty quiet. Or do you mean that there is no change at all when the switch is thrown and the stations come in just as they did before?

Steve Chambers
Find
Guest
Unregistered
 
#3

02-17-2006, 11:50 PM
Hi Steve,
Well, after I read your reply I had to go check again. Most all the reception is in the 1450 up area, but very, very faintly you can hear the local Hispanic station which broadcasts @ 960 AM. Not really a crisis, but made me curious.
Jim
« Next Oldest | Next Newest »
Thread Closed




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM
Testing a speaker and output transformer Trutone A2-G
morzh Short-circuited turns can be considered as a half-dead transformer. But on this case transformer will hot and s...Vlad95 — 11:01 AM
Testing a speaker and output transformer Trutone A2-G
I am not sure how a transformer could be weak. It could be inadequate, but only when you replace the original with somet...morzh — 09:56 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration