47-1227 - Radio will not tune in any stations.
Posts: 33
Threads: 3
Joined: May 2018
City: Middletown, PA
State, Province, Country: Pa
I have a Philco model 47-1227. It has been completely restored. All capacitors and resistors have been replaced. The audio works. We get sound from the record player but unable to tune in any stations. Have minis 2.5 volts at osc. tube. osc. tube does not change voltage when tuning dial is changed. No am or fm. Any ideal what's wrong? HELP!!!!!!!!?!
(This post was last modified: 06-09-2019, 06:53 PM by Lucky.)
Posts: 7,301
Threads: 269
Joined: Dec 2009
City: Roslyn Pa
Time to break out the signal generator and inject a modulated 455kc signal @ test point A. This is w/the set set up to receive an AM signal and see what you get from the spkr.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
Posts: 33
Threads: 3
Joined: May 2018
City: Middletown, PA
State, Province, Country: Pa
Receive nothing from test point A or when connected to antenna
Posts: 7,301
Threads: 269
Joined: Dec 2009
City: Roslyn Pa
Ok inject a 455kc signal @ pin 1 of the 6ba6 and see what you get from the spkr.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
Posts: 33
Threads: 3
Joined: May 2018
City: Middletown, PA
State, Province, Country: Pa
We get nothing from pin 1
Posts: 7,301
Threads: 269
Joined: Dec 2009
City: Roslyn Pa
How about pin 6 on the 7R7.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
Posts: 33
Threads: 3
Joined: May 2018
City: Middletown, PA
State, Province, Country: Pa
Pin 6 works with. Get loud tone
Posts: 33
Threads: 3
Joined: May 2018
City: Middletown, PA
State, Province, Country: Pa
06-09-2019, 08:38 PM
Pin 6 works. Hey loud tone.
(This post was last modified: 06-09-2019, 08:39 PM by Lucky.)
Posts: 7,301
Threads: 269
Joined: Dec 2009
City: Roslyn Pa
Ok so you have a problem around the 6BA6. Check the pin voltages according t o the service info. Also be sure the heater is lit.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
(This post was last modified: 06-09-2019, 08:46 PM by Radioroslyn.)
Posts: 33
Threads: 3
Joined: May 2018
City: Middletown, PA
State, Province, Country: Pa
pin 1. -.26 volts
pin 2. 0 volts
pin 3. 0 volts
pin 4. 0 volts
pin 5. 280 volts
pin 6. -1.14 volts
pin 7. .06 volts
Heater is lit
(This post was last modified: 06-09-2019, 09:09 PM by Lucky.)
Posts: 194
Threads: 43
Joined: Jan 2019
City: Brownsville 42210
State, Province, Country: Kentucky
filament should be pin 3 & 4 and pin 6 should be 100v
(This post was last modified: 06-09-2019, 09:48 PM by jake wells.
Edit Reason: error
)
Posts: 33
Threads: 3
Joined: May 2018
City: Middletown, PA
State, Province, Country: Pa
pin 3 grounded at center of tube
pin 4 shows 6.6 volts ac
The tube is lit and working
Posts: 194
Threads: 43
Joined: Jan 2019
City: Brownsville 42210
State, Province, Country: Kentucky
pin 6 should not be reading -1.14 it should be 100V check the resistors and capacitors in that circuit.
Posts: 33
Threads: 3
Joined: May 2018
City: Middletown, PA
State, Province, Country: Pa
Will check Tomorrow night.
Posts: 194
Threads: 43
Joined: Jan 2019
City: Brownsville 42210
State, Province, Country: Kentucky
Users browsing this thread: 1 Guest(s)
|
|
Recent Posts
|
|
462ron
|
|
It’s on the bottom of the homepage of our Philcoradio.com homepage!
Ron462ron — 07:20 AM |
|
Model 70 Cabinet Trim
|
| Steve might have some trim left.
Not sure he is making anything.morzh — 06:12 AM |
|
Model 70 Cabinet Trim
|
| Hello musar,
First all welcome to the forum and yes that is true that steve stopped making trim .
Sincerely Richar...radiorich — 12:13 AM |
|
Model 70 Cabinet Trim
|
| I have recently come into possession of a Model 70. The trim around the base needs to be replaced. If this were years ...musar — 12:07 AM |
|
philcorepairbench.com - shadow-meter
|
| Anyone know of a way to recover these files from the repair bench? Thanks.
fenbach — 11:16 PM |
|
Philco model 38 code 121 not receiving signal.
|
| That's true. Of course If I were to get a vtvm I'd probably have to sink money in to it to get it working right. Probabl...Stormlord5500 — 08:44 PM |
|
Philco model 38 code 121 not receiving signal.
|
| A DMM is good enough.
One rarely has to measure indictance, but if you do, short of getting a serious LCR meter (I hav...morzh — 07:35 PM |
|
Testing a speaker and output transformer Trutone A2-G
|
| You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now.
Have better volu...murf — 03:43 PM |
|
Philco model 38 code 121 not receiving signal.
|
| I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM |
|
Philco model 38 code 121 not receiving signal.
|
| I use a pair of Mastercraft brand DMMs from Canadian Tire, from what I read most of those DMMs use the same main chip re...Arran — 02:36 PM |
|
Who's Online
|
There are currently 241 online users. [Complete List]
» 1 Member(s) | 240 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
