Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Replacement for .7 to 1 interstage transformer
#1

Had a similar thread, but it wasn’t as specific as this, and therefore got lost. Anyone know a good replacement for this interstage transformer? Has a turns ratio of .7 to 1. It’s in a Sparton 28.

[Image: https://i.imgur.com/lNO85AP.jpg]
#2

It can not be .7 to 1.
Just by the sheer DC resistance, even if accounted for the wire gauge, 700 Ohm to 1 Ohm means huge difference in the number of turns.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#3

Morzh,

Look at the schematic. Primary at 3580Ω, secondary center-tapped at 2985Ω (or 5970Ω total secondary). equals a turns ratio of actually .599 to one, but close enough to the rated value of .7 to 1. Am I missing something here?
#4

Morzh,

Oh, I see. Your're looking at the output transformer. I'm referring to the input or interstage transformer.
#5

Oh..yes I was looking at the output.

38-116 has a similar one.
Lets' see if Tubes and More has something.
Nope. They have 1:2 and 1:3. Can't see that ratio around.
Maybe someone else can.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#6

I found a 1:1.5 but that was the lowest. Did find a 1:1 but was discontinued.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#7

1:1.5 and 0.7 to 1 are close enough.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#8

It's a Hammond 124D

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#9

Great! Thanks Terry. I'll get a 124D and give it a shot.

Pat




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco model 38 code 121 not receiving signal.
So one last question before I finish this radio. Regarding the speaker and output transformer. I salvaged the original o...Stormlord5500 — 09:31 AM
462ron
It’s on the bottom of the homepage of our Philcoradio.com homepage! Ron462ron — 07:20 AM
Model 70 Cabinet Trim
Steve might have some trim left. Not sure he is making anything.morzh — 06:12 AM
Model 70 Cabinet Trim
Hello musar, First all welcome to the forum and yes that is true that steve stopped making trim . Sincerely Richar...radiorich — 12:13 AM
Model 70 Cabinet Trim
I have recently come into possession of a Model 70.  The trim around the base needs to be replaced.  If this were years ...musar — 12:07 AM
philcorepairbench.com - shadow-meter
Anyone know of a way to recover these files from the repair bench? Thanks. fenbach — 11:16 PM
Philco model 38 code 121 not receiving signal.
That's true. Of course If I were to get a vtvm I'd probably have to sink money in to it to get it working right. Probabl...Stormlord5500 — 08:44 PM
Philco model 38 code 121 not receiving signal.
A DMM is good enough. One rarely has to measure indictance, but if you do, short of getting a serious LCR meter (I hav...morzh — 07:35 PM
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM

[-]
Who's Online
There are currently 1919 online users. [Complete List]
» 2 Member(s) | 1917 Guest(s)
AvatarAvatar

>