Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Magnavox 1FM031
#1

https://www.flickr.com/photos/92577012@N...9692099792

Why? Is a question that I ask myself sometimes, so who needs a 27 inch long radio? Guess I need a longer table. With the 2 large speakers it sounds very nice, even on AM. The FM could be a bit more sensitive but well in 1967 that may not have been a big worry. Case is nice, and it looks like a radio from the Dentist office that would play EZ Listening favorites. Hate to see it trashed because it is not Vacuum Tube.  Icon_eek

As I offloaded my last AM/FM Magnavox to a guy who is a FM Disc Jockey up here I now have a replacement. This is a better sounding set than that one, though the previous find had tubes. 

Paul

Tubetalk1
#2

It probably needs new electrolytic capacitors, especially in the FM section, and then possibly an alignment.

Impressive radio. I've seen pictures of those before but I did not know they were that large.

--
Ron Ramirez
Ferdinand IN
#3

I have cleaned the controls and it plays good though lytics need to go. I have not found too much documentation on this one. Fort Wayne Indiana.................

Paul

Tubetalk1
#4

Magnavox started out in Oakland, California and later moved to Fort Wayne, Indiana in 1931 by way of Chicago (1930). Fort Wayne was once the home of Slagle Radio, Steinite Radio, possibly others?

I just found a website dedicated to Magnavox history:
https://magnavoxhistory.com/

--
Ron Ramirez
Ferdinand IN
#5

My late friend Steve Hofer would roll over in his grave if I didn't mention that Farnsworth also had a factory in Ft. Wayne. Unfortunately the factory building has been torn down, but Philo's house remains.

Not to get too far off track, I like your new Magnavox Paul Icon_thumbup

John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
#6

Farnsworth - of course! Icon_redface Thanks John!

--
Ron Ramirez
Ferdinand IN
#7

Sweating it off up here today, off day today, back to grind tmrw. Listening to the Magnavox. My tube sets today a bit staticky, is that a word? Maybe too humid, when drizzly or moist I seem to get intereference from high tension lines out back. The solid state not so much. Sounds very fine for what it is. Very nice low end and bass but does not muddy higher end on music. So a good Magnavox product.

Has that heavy tuning feel like a german set, as a freind told me it's the flywheel effect on the tuner. Hope the heat breaks soon. Music and a cold one on a 98 degree day. Living high.

btw, nice website Ron, many pretty things.

How hot is it sez Ed McMahon, Johnny sez it's so hot ............

Paul.

Tubetalk1




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco model 38 code 121 not receiving signal.
Thank you sir. Yes I feel good and also relieved because this one's been weighing on me a bit.Stormlord5500 — 11:18 AM
Philco model 38 code 121 not receiving signal.
It feels good don't it? Good luck on the rest.Paul Philco322 — 11:06 AM
Philco model 38 code 121 not receiving signal.
I've reinstalled the coil. Now IT'S ALIVE!!!!!! I fired up my TinySA on signal generator mode and set it to 1400Kc and ...Stormlord5500 — 11:01 AM
Philco model 38 code 121 not receiving signal.
Yes, Walmart, right up there with Fluke.RodB — 11:00 AM
PT 6 chassis screws size???
it certainly won't be metric! SAE threads were all that was known then. Take care, - GaryGarySP — 10:58 AM
Philco model 38 code 121 not receiving signal.
I think this thing is way more accurate than my Walmart DMM. :DStormlord5500 — 08:19 AM
Philco model 38 code 121 not receiving signal.
Thankyou for the kind words sir. I double checked it with my component tester and it read 2.7 ohms at .02mH.Stormlord5500 — 08:14 AM
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM

[-]
Who's Online
There are currently 957 online users. [Complete List]
» 1 Member(s) | 956 Guest(s)
Avatar

>