Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

RCA Livingston
#1

Well we had a very nice event last Saturday up in New Hampshire sun came out and everything....well attended. I had brought some things up to get rid of and said no more radios to come home.....Well A friend of mine had this RCA, in 1954 it sold for 79.95! Big bucks. I also needed a few tubes and happened to find this Philco branded one I had not seen before. So a pretty good day. The Radio is heavy, large speaker, transformer powered. Who named it "Livingston"? Too much scotch at lunch for the AD Department. Did not see schematic in Nostalgia AIr so will look around.

I will probably keep this thing the case is not bad but some spots on the top molding. "Starlight" tube? Some guy from Ford must have thought that one up.

https://www.flickr.com/photos/92577012@N...9934835149

Paul

Tubetalk1
#2

Hi Paul, You will not be disappointed if you keep that RCA. It's a model 6RF9,9 tube, transformer powered powerhouse. I own 4 of them along with its earlier models, 1R81 and 3RF91. In my opinion the best American made tabletops ever made. The schematic is listed with the 3RF91. Good luck ,Bill
#3

Hey Paul from the diagram it looks like a strapping set!  https://worldradiohistory.com/Archive-Ri...n-1955.pdf  pgs 83-85

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#4

SWEET radio, Paul ! Good find ! I'll look forward to your posts on your restoration or refurbishment of it.
#5

The dial lights from both edges so should look god at nite. Inflation calculator sez 813.00 in todays dollars, hefty sum.

[Image: https://i.ebayimg.com/images/g/QVsAAOSw4...-l1600.jpg]

Paul

Tubetalk1




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently no members online.

>