Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

General Television - unknown model
#16

Lookin' good so far!! Wonder what would happen if you took to washing the grill cloth, it looks like that there is enough nicotine and tar on it to be positively carcinogenic!

"Do Justly, love Mercy and walk humbly with your God"- Micah 6:8
"Let us begin to do good"- St. Francis

Best Regards, 

MrFixr55
#17

I may try to give it a wash but to be honest I have had little success at washing these old grill cloths. In this case it’s almost invisible behind the wood grill and I do have some suitable replacement cloth so a wash might be worth a try.
#18

The washing worked out pretty well. Here's a before & after with the wash water in the middle. I used baby shampoo with warm water and very gentle movement of the cloth in the water for about 10 minutes. After washing I rinsed multiple times and then blotted it dry on paper towels and let it air dry. It could probably use another 10 min wash but I'm going to leave it where it is.

[Image: https://www.dropbox.com/s/eydr16icu2cpns....jpg?raw=1]
#19

That's an interesting pattern, considering that it is rather hidden behind a wooden grille. Wonder if they had i style for most of their radios with either an open face or a grilled face.

This is shaping up to being a real nice restoration!

"Do Justly, love Mercy and walk humbly with your God"- Micah 6:8
"Let us begin to do good"- St. Francis

Best Regards, 

MrFixr55
#20

The JB Weld filling the thread grooves for the knob set screw worked great. I retapped the threads without redrilling it. I also put in a slightly longer set screw so it would have an extra thread or two for grip. Set screw tightened down nicely. Thanks Gary, David and MrFixr.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM
Testing a speaker and output transformer Trutone A2-G
morzh Short-circuited turns can be considered as a half-dead transformer. But on this case transformer will hot and s...Vlad95 — 11:01 AM
Testing a speaker and output transformer Trutone A2-G
I am not sure how a transformer could be weak. It could be inadequate, but only when you replace the original with somet...morzh — 09:56 AM

[-]
Who's Online
There are currently 2219 online users. [Complete List]
» 2 Member(s) | 2217 Guest(s)
AvatarAvatar

>