Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

A Marconi model 86
#16

This Marconi was a bit of a challenge. It was totally missing one electrolytic  capacitor, and the photos show a couple of others taped [with hospital tape]
to the top of the chassis, with bare wires.

I had to rewire in the missing cap, and recap the radio.
   After going through everything and getting it fixed it does play very well.
 I had to take out the glass [four pieces] and clean them..

I had a junker Marconi  with tall cans  and they fit perfectly in the holes in the chassis where the original cans were
 Now comes the cabinet when it gets warmer. 

It still get down the near freezing at nigh,here in Calgary.
  I have a fellow turning me a knob to match the others..
It will be a nice radio after I get it done  [I hope].

Dan in Calgary


Attached Files Image(s)
                       

   Living in Calgary Alberta
#17

I have recapped this large Marconi model 86.  It plays quit good.
 
      I have stripped the cabinet and using Mohawk toned lacquer I did the areas that needed to be done.
 In these photos it is now ready for the final coats of clear lacquer 

 The cabinet is very solid and heavy,but well built

 When it is all done i will post more photos.
 Dan in Calgary


Attached Files Image(s)
               

   Living in Calgary Alberta
#18

Hello Dan,
Wow that cabinet looks incredible !!
I bet when it's all back together it will be a really nice set to enjoy .

Off, the subject how is the weather up there it hit 102 degrees here yesterday.

Sincerely Richard
#19

Thanks for the comment. The weather up here is quite nice. not too hot . It get s up to about 75F .
 Dan in Calgary

   Living in Calgary Alberta
#20

I like how the grille work is so sturdy yet pretty. So many radios with delicate grille work get broken and are hard to restore. Good luck with it. Paul

Tubetalk1
#21

Hi Paul;
 The grill pillars were quite easy to take out .They only had a rear nail in the top rear of each one.
          It is a lot easier to strip them when they are out.
The stripping on this radio was not as hard as some others I have done.
     I have seen photos of this model with the grill bars missing, and I wonder how that would happen,but some people don't care.
 I am glad I can get this one back to it's original look.
 Dan in Calgary

   Living in Calgary Alberta
#22

Dan, I love your cabinet work. If you enjoy it, do as much as you can now. I used to have the physical ability but my back and arthritis in my hands put an end to this kind of work. So I'll just admire your accomplishment.
#23

Thanks 
 I also have some arthritis in my hands, and it is getting a little harder to lift these radio cabinets
on and off so I can work on them. I find it very enjoyable to make the radios look like they came out of the factory.

  Sometimes I do change the toned lacquer a little, but many of the old radios were very dark and I lighten them up a bit.
     I am glad that the guys on any of the forums like the cabinets.
 I do get a lot of comments , so I must be doing something right.
Dan in Calgary

   Living in Calgary Alberta
#24

I like your approach to the dark finish. IMO to much dark finish hides some of the features of the cabinet. I used dark finish to highlight certain aspects.
#25

I have noticed that Marconi cabinets, from that era, didn't really go overboard with the shading lacquer, at least on the higher end cabinets. Unfortunately my only pre war Marconi is a model 157, and both ends of the cabinet were very heavily shaded, along with the grill, even the walnut veneer was over sprayed with tinted lacquer, though a more light colour.
Regards
Arran
#26

Well today I  installed the grill cloth board and the speaker.  The speaker must weigh 20 pounds by itself.
I put the chassis in the cabinet and it is now complete.

      It sounds very good in the cabinet and I really like the style.
 Here are the photos. The flash does not do the cabinet justice, but in person  it is a different story.
    Dan in Calgary


Attached Files Image(s)
                           

   Living in Calgary Alberta
#27

Hello Dan,
That really turned out very nice and I also like that color it is not to dark .

I Have General Electric model L-916 for 41 that I want to refinish the two big issues is part of it has photo finish and someone might have used some poly on part of it.

Sincerely Richard
#28

Those last photos were not very good,so I  used one of my other cameras. This is more like the true colors of the radio.
 Dan in Calgary


Attached Files Image(s)
                   

   Living in Calgary Alberta




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 42-345 Restoration/Repair
The thrill is gone again, thought I was close to being done with it. Well Friday it was receiving broadcast, Saturday mo...osanders0311 — 07:47 PM
Help with Supreme 599
Iam getting closer to fixing it. I bumped Up the tranny voltage to get 5v on the 80 tube. I gan get the needle to move ...daveone23 — 03:41 PM
Philco 42-345 Restoration/Repair
Hello RodB, Checking my previous post I realized you're the one with the 42-340. I replaced the string for the tuning...osanders0311 — 03:12 PM
5U4 vs 5Z4 tubes
I saw no evidence of anything going wrong. The transformer is fused already which is nice. Interestingly the 5z4 did...bridkarl — 02:37 PM
5U4 vs 5Z4 tubes
I doubt anything cooked in 30 seconds because of the oops! These are very similar tubes, and nothing but transformer re...GarySP — 02:30 PM
Restoration of the Canadian General Electric A-87
Paul Philco322.You will be keeping very busy, you may have to go back to work for a breakIcon_smile. Paul To rel...RadioSvit — 01:57 PM
5U4 vs 5Z4 tubes
I grabbed the wrong tube and put in a 5U4 tube instead of the 5Z4 - I just had the rectifier in with no other tubes. Af...bridkarl — 01:54 PM
Restoration of the Canadian General Electric A-87
After applying the filler to the entire body, I noticed that the shades of the facade and the side and top walls were ve...RadioSvit — 01:49 PM
Restoration of the Canadian General Electric A-87
You will be keeping very busy, you may have to go back to work for a break:). PaulPaul Philco322 — 01:46 PM
Restoration of the Canadian General Electric A-87
After removing the control knobs, chassis, dynamics and scale frame, I first started restoring the torn piece of veneer....RadioSvit — 01:20 PM

[-]
Who's Online
There are currently 832 online users. [Complete List]
» 2 Member(s) | 830 Guest(s)
AvatarAvatar

>