Zenith 6S254 Intermitten Reception
Posts: 18,427
Threads: 622
Joined: Oct 2011
City: Jackson
State, Province, Country: NJ
>>> It does not play at first power up of the day most times.
So you have to turn it on several times for it to play?
Have you looked at the volume control?
(I am not blaming the power switch as you said the voltages are OK when stopping playing)
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 1,799
Threads: 55
Joined: Feb 2015
City: Roseville, MN
When you have the problem the set goes quiet and the AVC drops to minimum. That tells me there's no, or very little, signal from the antenna.
When the ground is disconnected from the antenna does the problem occur? Maybe there's a strange ground loop. Usually a ground loop will result in interference or oscillation.
Posts: 555
Threads: 89
Joined: Jun 2022
City: Marion
State, Province, Country: NY
Volume control seems OK and I have sprayed it with Deoxit F5.
The AVC never varies much whether the reception is good or bad.
I will play the radio with ground disconnected and see how long it lasts.
Earlier this morning when I turned it on it was on the strong station and reception was bad. I turned up the volume to almost max and I could here the station with much noise. Currently the ground is disconnected tuned to strongest station in the area playing as expected with some noise. AVC voltage is -2.3. Off station AVC is -2.5 opposite what I would expect.
Posts: 1,799
Threads: 55
Joined: Feb 2015
City: Roseville, MN
With a strong station I expect to see -5 to -8 volts of AVC.
Posts: 555
Threads: 89
Joined: Jun 2022
City: Marion
State, Province, Country: NY
That is what I thought. So does that give us a clue?
Posts: 18,427
Threads: 622
Joined: Oct 2011
City: Jackson
State, Province, Country: NJ
Where are you measuring your AVC, and relative to what?
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 555
Threads: 89
Joined: Jun 2022
City: Marion
State, Province, Country: NY
On the 6H6 tube pin 8. Pin 4 and 8 are tied together. Positive probe on pin 8 negative probe on ground.
Posts: 1,799
Threads: 55
Joined: Feb 2015
City: Roseville, MN
Is the gimmick made with stranded or single strand wire? Might want to replace it with a 5pf cap.
Posts: 555
Threads: 89
Joined: Jun 2022
City: Marion
State, Province, Country: NY
Stranded wire. Where do I connect the cap. I assume osc section to ant section of tuning cap?
Posts: 1,799
Threads: 55
Joined: Feb 2015
City: Roseville, MN
The gimmick should have two wires connected. The cap leads go where the gimmick wires are soldered in.
Posts: 18,427
Threads: 622
Joined: Oct 2011
City: Jackson
State, Province, Country: NJ
What you are measuring is mostly voltage created by the Candohm divider between the 27 Ohm and 128 Ohm sections.
And NOT the AVC.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 555
Threads: 89
Joined: Jun 2022
City: Marion
State, Province, Country: NY
When I first got the radio the gimmick was connected to the osc section and wrapped around the wire going from ant section to the 6A8 grid. Only one side of gimmick was connected. So not sure how to wire 5pf cap.
Posts: 555
Threads: 89
Joined: Jun 2022
City: Marion
State, Province, Country: NY
Where do I measure the AVC?
Posts: 18,427
Threads: 622
Joined: Oct 2011
City: Jackson
State, Province, Country: NJ
I think the filtered AVC is C12/R5 connection. Which will be the same voltage as on the Grid of 6A8. (G4, the Grid cap)
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 555
Threads: 89
Joined: Jun 2022
City: Marion
State, Province, Country: NY
Ok. I get a decent swing of AVC on the 6A8 grid.
Users browsing this thread: 2 Guest(s)
|
|
Recent Posts
|
|
54C Cabinet Refinish
|
| hello Roy,
I’d follow Arran’s suggestion and use automotive gasket material, which I keep around for situations like th...radiorich — 10:22 PM |
|
Philco 71 Code 125
|
| This might be one of those cases where it's a ground to an AC voltage and B- to DC.RodB — 08:22 PM |
|
Philco 71 Code 125
|
| Really Rod? I know you would not steer me wrong but AI say this is a short circuit? What if I moved the 6 volt center ta...dconant — 06:40 PM |
|
54C Cabinet Refinish
|
| Roy;
Personally I would have left the asbestos alone if it were my set, but you can find a modern substitute that som...Arran — 04:51 PM |
|
Philco 71 Code 125
|
| Looks like that might be the B- buss, so that would be correct.RodB — 01:32 PM |
|
Philco 71 Code 125
|
| I noticed on the code 121 schematic the center tap for the 6 volt winding and hv winding are tied together. Is this corr...dconant — 12:16 PM |
|
Philco 45-6365 Universal IFT Instruction Manual
|
| The Philco Parts Catalog for 1942 shows it as usable for 175 kHz, 260 kHz, and 465 kHz. The instructions will show how t...DaleHCook — 11:19 AM |
|
Stromberg Carlson 1500 Squeal
|
| Hello Rob,
I agree with you—I have one here at my house that I need to check out. It’s way over-engineered just to make...radiorich — 11:05 AM |
|
My Atwater Kent 84
|
| Well getting around to restoring my AK84. Mike was a big part in me being able to snatch this one a few years ago. I won...462ron — 10:57 AM |
|
Plug Voltages Needed For A 1943 CRV-20130 Power Supply
|
| The engine is a B&S 23 inch cast Iron holds 2 quarts of oil. The Generator is a 4 pole 1800 rpm mine was made in 195...David — 10:51 AM |
|
Who's Online
|
There are currently 2015 online users. [Complete List]
» 2 Member(s) | 2013 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
