Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

volume control
#1

Can someone tell me the resistance of a philco 7439 volume control.
#2

If it is for the model 80 it's 20K. Two quick checks, one unplug set turn volume all the way up. Measure resistance from ANT post to chassis ground. Should be very low like a few ohms. If not antenna coil primary is open. Two, Turn volume all the away down.Measure resistance from antenna post to chassis ground. Should read about 20,000 ohms. If not check volume control, open or bad ground connection.
How's your oscillator doing?
Terry

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#3

What model Philco are you working on?

I didn't see any data on your part number on Philcorepairbench.com.

-Keith
#4

Terry is correct, it is 20K. Part no. 7439 was used in model 80 and the three-knob 81.

--
Ron Ramirez
Ferdinand IN
#5

Do I get a prize????
Terry

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#6

Yeah - a Philco 84B that needs complete restoration. Icon_twisted Icon_lol

--
Ron Ramirez
Ferdinand IN
#7

I unsoldered one outer lug, not the one to ground and measured it like a resistor, 17 ohms.
Strange, then I unsoldered the center lug and it read 27k. I thought you can measure a pot like a resistor if one of the outer lugs is disconnected.
#8

Depending on the circuit this may not be true, IE this case. However if the wiper is all the way toward the still connected end you should be able to get an accurate reading. Then you could connect the ohmmeter between the center and unconnected end and sweep it, and you will then see if there are any open spots.
#9

It also maybe effected by the very low resistance of the antenna coil connected to the wiper and ground.
Terry

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry




Users browsing this thread:
[-]
Recent Posts
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM
Testing a speaker and output transformer Trutone A2-G
morzh Short-circuited turns can be considered as a half-dead transformer. But on this case transformer will hot and s...Vlad95 — 11:01 AM
Testing a speaker and output transformer Trutone A2-G
I am not sure how a transformer could be weak. It could be inadequate, but only when you replace the original with somet...morzh — 09:56 AM

[-]
Who's Online
There are currently 2224 online users. [Complete List]
» 2 Member(s) | 2222 Guest(s)
AvatarAvatar

>