1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
RF Choke winding on capacitor
lasurveyor
Member
***
Posts: 90
Threads: 32
Joined: Oct 2011
City: Nipomo State, Province, Country: CA
#1

11-25-2011, 07:35 PM
Hi All,

When re-capping 1940's ac-dc table top Philcos, there is a .2 mf cap with one lead wound around the cap and called an RF Choke. Can I just replace the cap and ignore this winding?

Alan
Find
codefox1
Silent Key
*****
Posts: 2,128
Threads: 18
Joined: Oct 2008
City: Merrick, Long Island, NY
#2

11-25-2011, 08:19 PM
Yes. Been covered many times. Don't worry about it.
Find
TexMac
Member
**
Posts: 12
Threads: 0
Joined: Jun 2010
City: Leesburg, TX
#3

12-16-2011, 11:27 PM
In most cases a plain new cap will work ok. BUT count the turns and save the old cap tube because when it starts to scream at you when it goes into oscillation, you just might need to reproduce it on some sets. Been there, done that, waiting on my T-shirt. Now, since I restuff anyway, I just reproduce them. I figure it can't hurt.
Ron Mc/
Find
Texasrocker
Phorum Expert
*****
Posts: 909
Threads: 117
Joined: Jun 2007
#4

12-16-2011, 11:49 PM
As Codefox said, get rid of it. Not needed at all.
Find
« Next Oldest | Next Newest »
Thread Closed




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration