Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Grillecloth for a Model 41-285 Console
#1

Dear Philco Phorum friends, I have the Grillecloth Headquarters order sheet, and Web site address, do any of those patterns Accurately represent the proper pattern for the Philco Model 41-285 console?? My old cloth is so plain and faded I can't even tell the original color, just the weave of the cloth. Just putting the finishing touches on this one and wan't to keep it as close to original as possible. Any help on this one would be greatly appreciated. Thanks, BOBC.
#2

BOBC - can you post a picture or scan of the old cloth you now have? I don't have an actual photo of this model so I can't compare it to anything. Thanks.

--
Ron Ramirez
Ferdinand IN
#3

Thanks for the reply Ron, actually I don't have a scanner or dockable digital camara right now, but I think the original piece of cloth will do upon further cleaning and removal of mud wasp nests from the cloth! I don't believe the cloth was the focal point for the radio as there were 9 wooden slats across the grill area with no more than a pinkey space between each slat, so you really can't see but thin views of the background cloth. I guess knowing the intact cloth is original is good enough for me right now. Sorry I couldn't show the cloth pic, but thank you for responding just the same. BOBC




Users browsing this thread:
[-]
Recent Posts
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM
Testing a speaker and output transformer Trutone A2-G
morzh Short-circuited turns can be considered as a half-dead transformer. But on this case transformer will hot and s...Vlad95 — 11:01 AM
Testing a speaker and output transformer Trutone A2-G
I am not sure how a transformer could be weak. It could be inadequate, but only when you replace the original with somet...morzh — 09:56 AM

[-]
Who's Online
There are currently 2256 online users. [Complete List]
» 2 Member(s) | 2254 Guest(s)
AvatarAvatar

>