Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

MODEL 41-629P (?)
#1

This is my first posting. I'm not a collector, but I do have an old cabinet I need help with.

I have what appears to be the cabinet for a MODEL 41-629P. The lady I got it from, a German war bride, has a photo of the unit from about '45, taken in her husband's home in the States. In the photo, the cabinet is black.

Her late husband stripped it of its electronics and turned it into a bar. I got it with the intent of refinishing it and turning into a wine caddy with a chiller in the bottom.

I began stripping it only to find it has (what seems to be) the typical finished wood veneer, most of which is okay, but needs some work. The lid may not be original as it's not veneered, nor does it seem to have been.

Questions:
-What type wood veneer was used? Is there a source for replacment veneer?
-Can anyone speculate why this unit would have been painted black prior to '45? Was it a factory cover job for less than acceptable finishes?
-For its intended purpose, should I refinish it black or in it's varnished veneer condition? (I like both.)

Thanks, all! I look forward to hearing from you!

Ed
#2

couldn't find any literature that said they painted them black....can't give you much information beyond that.....owner could have painted it black to cover up blemishes himself ie...guess...sorry not much help....Terry




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM
Testing a speaker and output transformer Trutone A2-G
morzh Short-circuited turns can be considered as a half-dead transformer. But on this case transformer will hot and s...Vlad95 — 11:01 AM
Testing a speaker and output transformer Trutone A2-G
I am not sure how a transformer could be weak. It could be inadequate, but only when you replace the original with somet...morzh — 09:56 AM

[-]
Who's Online
There are currently 2137 online users. [Complete List]
» 2 Member(s) | 2135 Guest(s)
AvatarAvatar

>