Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Not sure what i have...HELP??
#1

Can someone tell me how to find out info about a set i have...it is a philco console, but i can't find a pic like it on here. the face of the radio is on the upper front, has wooden buttons for selction, but also has 4 large dials on either side of the face. Has several different countries listed on the face/...along with AM and aircraft and several more..don't remember the others and i am not where it is at the moment...if someone could point me in the right direction i would be most thankful

Deb (sorry don't have a pic at the moment)
#2

Hi Deb and Welcome to the Phourm!!!
Without a pic it going to be tough! You maybe able to find a small blue and white sticker on the inside of the cabinet that will display the model number. It may also be stamped in ink on the chassis. Most of the time it will be two digits a dash and one-three more digits. The first two will be the year it was made. Did you have a look in the Gallery??
Terry
#3

Thanks Terry, i kept looking thru the gallery and think i found one that is pretty close...It looks like the 40-215RX only the buttons are closer together and are wooden
#4

Philco never used wood push buttons. They where tenite which is an early type of plastic. Not known for it's longevity most have badly deteriorated by now. Replacements are available. Maybe someone hand carved wooden replacements?
Terry
#5

Hello, Deb: try to get a pic to post here on the Phorum, that would be a major help in pin-pointing what you have.
#6

She figured out at it's a 41-295. Now she try to find it's worth. I gave a few ideas...
Terry
#7

Zehr gut!!!




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
462ron
It’s on the bottom of the homepage of our Philcoradio.com homepage! Ron462ron — 07:20 AM
Model 70 Cabinet Trim
Steve might have some trim left. Not sure he is making anything.morzh — 06:12 AM
Model 70 Cabinet Trim
Hello musar, First all welcome to the forum and yes that is true that steve stopped making trim . Sincerely Richar...radiorich — 12:13 AM
Model 70 Cabinet Trim
I have recently come into possession of a Model 70.  The trim around the base needs to be replaced.  If this were years ...musar — 12:07 AM
philcorepairbench.com - shadow-meter
Anyone know of a way to recover these files from the repair bench? Thanks. fenbach — 11:16 PM
Philco model 38 code 121 not receiving signal.
That's true. Of course If I were to get a vtvm I'd probably have to sink money in to it to get it working right. Probabl...Stormlord5500 — 08:44 PM
Philco model 38 code 121 not receiving signal.
A DMM is good enough. One rarely has to measure indictance, but if you do, short of getting a serious LCR meter (I hav...morzh — 07:35 PM
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM
Philco model 38 code 121 not receiving signal.
I use a pair of Mastercraft brand DMMs from Canadian Tire, from what I read most of those DMMs use the same main chip re...Arran — 02:36 PM

[-]
Who's Online
There are currently 228 online users. [Complete List]
» 2 Member(s) | 226 Guest(s)
AvatarAvatar

>