Could someone pat me on the back?
Posts: 193
Threads: 50
Joined: Oct 2011
City: York PA
I'm floating around in radio ecstasy. Let me describe what I started with: A Philco 77 from CL for $25. The speaker was badly smashed-in, but for fun I repaired the cone with low expectations. It had no 45s and the ones I'm using test poor. The filter can had been removed and a 20/20 uF with mid-air solder joints was for, I guess, the 2.0 uFs, although there are three! The 2 bakelite blocks are gone and in their place was the worst unsupported mid-air soldering job that I've ever seen. The input xformer is replaced. After a lot of scrutinizing of the schematic, I made nice terminal strips for the bakelite blocks and made a new filter cap board. My hopes are really low at this point because the drawing that I made of the old wiring job, did not appear to match the new work that I completed. So with nothing to lose, I variac-ed it up and at 70 volts, I couldn't believe my ears, it works  .
Posts: 5,170
Threads: 274
Joined: Nov 2012
City: Wilsonville
State, Province, Country: OR
Posts: 298
Threads: 22
Joined: May 2012
City: Chattanooga
State, Province, Country: TN
It's not how bad you mess up, it's how well you can recover.
Posts: 16,507
Threads: 572
Joined: Oct 2011
City: Jackson
State, Province, Country: NJ
Hey! There you go, man! Feels almost sexual, doesn't it!
Really happy for ya!
Posts: 54
Threads: 8
Joined: Nov 2012
City: Wilton, Iowa
Congrats on your success. From wondering IF --- to euphoria.
Jim
Posts: 2,128
Threads: 18
Joined: Oct 2008
City: Merrick, Long Island, NY
Problem is you're hooked, but congrats anyway.
Posts: 193
Threads: 50
Joined: Oct 2011
City: York PA
I didn't mention that the dial cord was broken, as well. So I laid the 2 old pieces out on my bench to find the length and cut a new one and knotted on the springs. There's some hope involved here, of course. So I string it on and it seems like it's maybe a half inch short. Not wanting to start over and having dealt with this chore before, I grabbed the end of the spring with my needle nose and pulled. By some miracle, the end went into the hole and after a few complete spins of the dial, it's just right! What a day! It's bright green masons' snap-line, so don't tell anyone.
Posts: 1,562
Threads: 56
Joined: Nov 2008
City: Sedona, AZ/Placentia/CA
Nice job and well, not exactly a sexual high for me, it could have been if I was working on it. Happy for you.
Jerry
A friend in need is a pest! Bill Slee ca 1970.
Posts: 4,894
Threads: 54
Joined: Sep 2008
City: Sandwick, BC, CA
Did someone remove the sheet metal can block capacitor? If so that was quite a job since it has at least 1/2 dozen other caps in it as well. Since it is a 1929-30 model it would not have stand alone wet electrolytic cans.
Regards
Arran
Posts: 193
Threads: 50
Joined: Oct 2011
City: York PA
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand
State, Province, Country: Indiana
Quote:not exactly a sexual high for me
[Image: http://i326.photobucket.com/albums/k420/...isgust.jpg]
Anyway, here's your pat on the back. Sorry, it's en Espanol.
[Video: https://www.youtube.com/watch?v=-Cx25-Ri2bI]
--
Ron Ramirez
Ferdinand IN
Posts: 1,562
Threads: 56
Joined: Nov 2008
City: Sedona, AZ/Placentia/CA
DK, I replaced at ruinous expense two of those tubes that both measured between 8 and 10% on my cheap tube tester with NOS tubes. No real difference in performance. Of course they were "matched" for low emission! Sorry about my previous response if inappropriate Ron. Just felt Mortzh's threshold for excitement was a little low.  Sorry Mortzh.
Jerry
A friend in need is a pest! Bill Slee ca 1970.
(This post was last modified: 02-10-2013, 10:58 PM by jerryhawthorne.)
Posts: 16,507
Threads: 572
Joined: Oct 2011
City: Jackson
State, Province, Country: NJ
Jerry
I said "feels sexual", but I did not imply the intensity of it 
Then again, as we say in my language "where there's no fish crayfish is the fish!". So, depends on what alternatives you have.
This is why in my language when we do mean long and hard (sorry - no allusions here) frustrating dealing with some problem, we actually use the equivalent of the "f" verb. So at the end of that, some ..well...high...should come!
Posts: 1,562
Threads: 56
Joined: Nov 2008
City: Sedona, AZ/Placentia/CA
I agree, some high should come. It does for me as well when a radio starts to play. Thanks for the explanation. Certainly changing from one language to another involves subtle differences. I like you Morzh!
Jerry
A friend in need is a pest! Bill Slee ca 1970.
Posts: 33
Threads: 8
Joined: Jan 2011
My Grandpa always said "a pat on the back is awfully close to a kick in the butt"
Users browsing this thread: 1 Guest(s)
|
|
Recent Posts
|
|
Philco 42-345 Restoration/Repair
|
| Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM |
|
Philco 42-345 Restoration/Repair
|
| Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM |
|
Philco model 38 code 121 not receiving signal.
|
| Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM |
|
Testing a speaker and output transformer Trutone A2-G
|
| The equivalent of one short turn is basically the same as that of a shorted load.
If it is the primary's turn, then the ...morzh — 03:53 PM |
|
Testing a speaker and output transformer Trutone A2-G
|
| I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM |
|
Philco model 38 code 121 not receiving signal.
|
| As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM |
|
Philco model 38 code 121 not receiving signal.
|
| Well why not! :lol:Stormlord5500 — 03:14 PM |
|
Philco model 38 code 121 not receiving signal.
|
| Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM |
|
Testing a speaker and output transformer Trutone A2-G
|
| morzh
Short-circuited turns can be considered as a half-dead transformer.
But on this case transformer will hot and s...Vlad95 — 11:01 AM |
|
Testing a speaker and output transformer Trutone A2-G
|
| I am not sure how a transformer could be weak. It could be inadequate, but only when you replace the original with somet...morzh — 09:56 AM |
|
Who's Online
|
| There are currently no members online. |
|
 
|
. Anyway, new question: The one 45 tests almost GOOD and the other one is down in the BAD. Does that explain why the one tube, while lit, is practically cold while the other one is hot?
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
