Posts: 1,531
Threads: 242
Joined: Sep 2012
City: West Bend, Wisconsin
Greg V.
West Bend, WI
Member WARCI.org
Posts: 7,301
Threads: 269
Joined: Dec 2009
City: Roslyn Pa
Nice Job! Look lke an eastern set, most of those stations I can get over here. WCAU is WPHT now as of 10 or so years ago. I don't understand why stations change call signs after many many years. Kinda like us hams the FCC has allowed us the to have call signs which don't necessarily have to be in the call district we are in. It's a bit of annoyance you think the guy is in Calf. but he's next door.
Terry
Posts: 52
Threads: 1
Joined: Mar 2013
City: Minneapolis, MN
Any stray capacitance between the 75 grid cap and the plate of the output tube ( 41, 42, etc.) can cause hi freq audio oscillation. Dress the grid lead away and/or try some shielding.
Posts: 761
Threads: 56
Joined: Jul 2013
City: Kentucky
Beautiful radio. Great job!
The artist formerly known as Puhpow! 8)
Posts: 120
Threads: 10
Joined: Jul 2011
City: Glendale, CA
I've got a 39-30 as well. I have seen some 39-30's with only 1 tube shield, on the 75 tube. For whatever reason, my radio has provisions for two tube shields, on the 75 and the 37. But, when I got it, it only came with only 1 actual tube shield installed, on the 75. Could that be part of your problem?
Tom
Posts: 2,353
Threads: 92
Joined: May 2010
City: Clayton, NC
Bill/Tom: great advice. Funny thing about 75 tubes, the mutual conductance of the triode is only 750 uMhos, and it doesn't take long for it to degrade to the 500 range. In sets where the 75 is the only AF amp before the output tube this can be an issue.
Also: 42 tubes can be noisy after they warm up. Same goes for 6F6 tubes.
Posts: 2,353
Threads: 92
Joined: May 2010
City: Clayton, NC
Posts: 1,531
Threads: 242
Joined: Sep 2012
City: West Bend, Wisconsin
Mine only has one tube shield too over the 75 tube.
Greg V.
West Bend, WI
Member WARCI.org
Posts: 77
Threads: 24
Joined: Nov 2010
City: Oradell, NJ
Quote:It took three #75 tubes until I found a good one that didn't cause a muffled hissing after the set played for about 5 or 10 minutes
That might have been a supersonic parasitic oscillation. A "grid stopper" resistor, around 68K, placed in series with the grid wire right at the top cap of this tube (its grid), should tame those unruly tubes you have. This resistor, in combination with the tube's stray capacitance, acts like a low pass filter to disable the oscillation.
(This post was last modified: 09-20-2013, 04:33 PM by wa2ise.)
Posts: 61
Threads: 2
Joined: Aug 2013
City: Renton, Wa
Real nice looking set--great restoration !
Posts: 1,531
Threads: 242
Joined: Sep 2012
City: West Bend, Wisconsin
Thanks, everyone. The set is working fine now. I think it had a lot to do with shielding around that 75 tube. No more muffled hissing. 
Greg V.
West Bend, WI
Member WARCI.org
Posts: 1,531
Threads: 242
Joined: Sep 2012
City: West Bend, Wisconsin
I really like the rear lighted dial on these 1939's. And, using the "Rebuilding Philco Pilot Lamps" tip found in the tech section ( http://philcoradio.com/tech/lamps.htm ) it no longer flickers on and off! 
Greg V.
West Bend, WI
Member WARCI.org
Posts: 481
Threads: 18
Joined: Jan 2013
City: Mesa, AZ
Still love those wine flavored buttons! 
Posts: 4,902
Threads: 54
Joined: Sep 2008
City: Sandwick, BC, CA
Another thing to watch for on a 75 tube, or any other glass tube with a grid cap, is the solder joint on the grid cap giving out. Also the clip on the end of the grid lead can have problems, the solder joint going bad or the wire breaking internally.
Regards
Arran
Posts: 825
Threads: 113
Joined: Aug 2012
City: The Villages
State, Province, Country: Florida
Wow. Really great restoration! 
Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org
Users browsing this thread: 3 Guest(s)
|
|
Recent Posts
|
|
Electrolytic restuffing/internals
|
| I don’t have a vise so I had to hold it in my
hand. Not optimal but covered up by the hvac
tape in the end.
I have a few...bridkarl — 11:52 PM |
|
Electrolytic restuffing/internals
|
| Bridkarl
A question.
For a hacksaw the cut looks a little...jagged. Why?morzh — 11:45 PM |
|
The list of my radio & TV collection!
|
| As usual, an interesting post from you, Peter. This seems to be similar to the RCA 3-BX-671 and the Zenith Transoceanic...MrFixr55 — 11:41 PM |
|
The list of my radio & TV collection!
|
| Hello Peter,
Thank you for sharing your new video and looks like your weather is nice their too.
it was like 25 Cel...radiorich — 11:05 PM |
|
Electrolytic restuffing/internals
|
| hello bridkarl,
I will post some better photos !
Sincerely Richardradiorich — 10:14 PM |
|
Electrolytic restuffing/internals
|
| I just taped the two pieces of the cap together, but I can see your method is better. I just held the lead in with solde...bridkarl — 08:18 PM |
|
Electrolytic restuffing/internals
|
| hello bridkarl,
Well done !
Here is a Photo of the base of Philco capacitor that I cut open you can see how I glued th...radiorich — 08:14 PM |
|
philco predicta
|
| Hi CGL18,
Here is a link for the schematic from the Early television Foundation:
WARNING!! One side of the Chassis i...MrFixr55 — 08:09 PM |
|
The list of my radio & TV collection!
|
| Peter;
I like Canadian General Electric sets, whilst the model numbers are often the same as their U.S General Electr...Arran — 05:44 PM |
|
Electrolytic restuffing/internals
|
|
Did as suggested. Cut can with hacksaw, removed internals, attached new 8mf cap - with ample use of cardboard and elec...bridkarl — 03:36 PM |
|
Who's Online
|
| There are currently no members online. |
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
